Read Sony DCR-DVD305 (serv.man3) Service Manual online
6-77
DCR-DVD305
3-3.
APPLICATION FOR ADJUSTMENT
(SeusCam)
(SeusCam)
The adjustment software (SeusCam) can change operational coef-
ficients of signal processing, EVR data, etc. same as the adjust-
ment remote commander. The SeusCam performs two-way com-
munication between PC and camcoder using the USB terminal.
The two-way communication result data can be written in the non-
volatile memory.
ficients of signal processing, EVR data, etc. same as the adjust-
ment remote commander. The SeusCam performs two-way com-
munication between PC and camcoder using the USB terminal.
The two-way communication result data can be written in the non-
volatile memory.
Note 1:
The SeusCam is used exclusively for the camcoders
(DCR, DHR, CCD, etc.). It cannot be used for digital
cameras (DSC, MVC, etc.).
(DCR, DHR, CCD, etc.). It cannot be used for digital
cameras (DSC, MVC, etc.).
Note 2:
Before using the SeusCam, set the following data using
the adjustment remote commander.
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 14, set data: 01, and press
the adjustment remote commander.
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 14, set data: 01, and press
the PAUSE (Write) button.
After use, release the set data.
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 14, set data: 00, and press
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 14, set data: 00, and press
the PAUSE (Write) button.
3) Select page: 0, address: 01, and set data: 00.
1.
Connection
1) Connect the HASP key to the USB terminal of the PC.
2) Connect the PC and camcoder with the USB cable.
3) Start the SeusCam on the PC.
4) Click
2) Connect the PC and camcoder with the USB cable.
3) Start the SeusCam on the PC.
4) Click
[Connect]
on the SeusCam screen. If the connection is
normal, the SeusCam screen will be as shown in Fig. 6-3-3,
indicating the
indicating the
“connected”
state.
Note:
The SeusCam will go in
“disconnect” state, if the set is
turned off (for instance, by resetting the set). In such a
case, click
case, click
[Connect]
on the SeusCam screen to re-
store the
“connected”
state.
2.
Operation
• Page change
To change the page, click
[Page]
on the SeusCam screen and
enter the page to be changed. The page is displayed in hexa-
decimal notation.
decimal notation.
• Address change
To change the address, click
[Address]
on the SeusCam screen
and enter the address to be changed. The address is displayed in
hexadecimal notation.
hexadecimal notation.
• Data change
To change the data, click
[Set]
on the SeusCam screen and en-
ter the data. The data is displayed in hexadecimal notation.
This operation does not write the data to the nonvolatile memory.
This operation does not write the data to the nonvolatile memory.
• Data writing
To write the data to the nonvolatile memory, click
[Write]
on
the SeusCam screen and enter the data to be written.
• Data reading
The data displayed on the SeusCam screen are the data values
at the time when the pages and addresses were set, and they are
not updated automatically. To check the data change, click
at the time when the pages and addresses were set, and they are
not updated automatically. To check the data change, click
[Read]
on the SeusCam screen and update the displayed data.
3.
Difference in Display Between SeusCam and
Adjustment Remote Commander
Adjustment Remote Commander
There is no difference in display of address and data between
SeusCam and adjustment remote commander. Though the page is
displayed in one digit on the adjustment remote commander, it is
displayed in two digits on the SeusCam.
The “page 1A” or “page 1F” is selected after setting data: 01 to
the page: 0, address: 10 on the adjustment remote commander,
while it can be selected by clicking the
SeusCam and adjustment remote commander. Though the page is
displayed in one digit on the adjustment remote commander, it is
displayed in two digits on the SeusCam.
The “page 1A” or “page 1F” is selected after setting data: 01 to
the page: 0, address: 10 on the adjustment remote commander,
while it can be selected by clicking the
[Page]
and entering “1A”
or “1F” on the SeusCam. For the “page A” or “page F”, enter “0A”
or “0F”.
or “0F”.
4.
Precaution on Use of SeusCam
Wrong SeusCam operation could clear correct adjustment data.
To prevent the data clear by mistake, it is recommended to save all
adjustment data by clicking
To prevent the data clear by mistake, it is recommended to save all
adjustment data by clicking
[Page Edit]
on the SeusCam screen
before starting the adjustment.
Saving Method:
1) Click
1) Click
[Page Edit]
on the SeusCam screen to display the SeusCam
Page Edit screen.
2) Click
[Page]
, and enter the page number to be saved.
3) Click
[Read]
to read the data to be saved from the camera.
4) Click
[File]
and save the data to PC.
Loading Method:
1) Select page: 00, address: 01 and set data: 01.
2) Click
1) Select page: 00, address: 01 and set data: 01.
2) Click
[Page Edit]
on the SeusCam screen to display the SeusCam
Page Edit screen.
3) Click
[File]
and load the data from PC.
4) Click
[Write]
on the SeusCam Page Edit screen.
Fig. 6-3-3
Click on the first or last page to see other DCR-DVD305 (serv.man3) service manuals if exist.