Read Sony DCR-DVD203 (serv.man2) Service Manual online
• Para Manual de Intrução, consulte MANUAL DO SERVIÇO, LEVEL 1
inside the CD-564, VF-167, MD-114, MD-120 and VC-396 board.
Therefore, schematic diagram, printed wiring board, waveforms, mounted parts location and electrical parts list of the CD-564,
VF-167, MD-114, MD-120 and VC-396 board are not shown.
The following pages are not shown.
Electrical parts list .............................. Pages 5-16 to 5-28
Printed wiring board ............................ Pages 4-77 to 4-94
Waveforms ........................................... Pages 4-96 to 4-97
0 lx (lux) (in the NightShot
established by the JEITA (Japan Electronics
and Information Technology Industries
Association). Files in this format can have
additional information such as your camcorder’s
setting information at the time of recording.
fi gures resulting from wide angle pixel readout.
shot with infrared lighting.
Video signal: 1 Vp-p, 75
Luminance signal: 1 Vp-p, 75
impedance 47 k
NP-FP50 rechargeable battery
pack and disc
Dolby Digital 5.1 Creator
(VIDEO mode), DVD-
VideoRecording (VR mode)
LP: Approx. 60 min
(Charge Coupled Device)
Approx. 1 070 000 pixels
Effective (Movie) :
Approx. 690 000 pixels
Effective (Still) :
Approx. 1 000 000 pixels
Filter diameter:30mm (1 3/16
Optical:12, Digital:24, 480
When converted to a 35 mm
46 - 628.5mm (1 13/16 - 24 3/4
in.) (16:9 mode)
in.) (4:3 mode)
For still images:
40 - 480mm (1 5/8 - 19 in.)
connections. Check the entire board surface for solder splashes
"pinched" or contact high-wattage resistors.
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
of deterioration. Point them out to the customer and
recommend their replacement.
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
• Unleaded solder melts at a temperature about 40
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
heated tip is applied for too long, so be careful!
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
also be added to ordinary solder.
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
Replace only with the same or equivalent type.
One is the MD-114 board and the other is the MD-120 board.
Method of identifying the two different MD boards is shown on page 6.
Use of controls or adjustments or performance
procedures other than those specified herein may
result in hazardous radiation exposure.
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION,
BE SURE TO OBSERVE FROM A DISTANCE OF MORE
THAN 30 cm FROM THE SURFACE OF THE
OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
The use of optical instrument with this product will increase eye