Read Sony SDM-S75A / SDM-S75D / SDM-S75E / SDM-S75F / SDM-S95A / SDM-S95AR / SDM-S95D / SDM-S95DR / SDM-S95E / SDM-S95ER / SDM-S95F / SDM-S95FR Service Manual online
SDM-S75A,D,E,F/ SDM-S95A,AR,D,DR,E,ER,F,FR (E)
16
ADJUSTMENT
1. Procedures of how to go to service mode.
1) Enter the service mode of this unit by turning on the
power while pressing and holding the "↓" key
simultaneously.
simultaneously.
2) Press "MENU" key----MAINTAIN.
3) Press "OK" key to enter the service menu.
4) Select the desired function.
5) Press the "MENU" key to exit OSD.
6) Turn off the power and then turn on it again. The
3) Press "OK" key to enter the service menu.
4) Select the desired function.
5) Press the "MENU" key to exit OSD.
6) Turn off the power and then turn on it again. The
monitor then enters the normal mode.
To enter the service again, repeat the procedure
described above.
To enter the service again, repeat the procedure
described above.
Note
W/B readjustment is required after the panel, board
and microcomputer are replaced. However, be sure to
perform aging for more than 30 minutes for RGB
reset before W/B adjustment.
and microcomputer are replaced. However, be sure to
perform aging for more than 30 minutes for RGB
reset before W/B adjustment.
2. Setup
1) Prepare timing and pattern data for a signal
generator according to the Sony timing specifications.
2) Connect a monitor video cable to the signal
generator.
3) Put Color Analyzer (ex. CA-110) 50cm away from the
monitor, specify it vertically in the center of the display,
and adjust the focus to the optimum level using an
eyepiece.
and adjust the focus to the optimum level using an
eyepiece.
4) Put the monitor and Color Analyzer (ex. CA-110) in a
light-shielded room.
5) Set up [SERVICE MODE] of the monitor.
3. Operation
Data is manually set to improve the productivity. The
brightness, contrast, and backlight are set to 50, 70 and
100 respectively. After that, the default data of the color
temperature to be adjusted is set.
brightness, contrast, and backlight are set to 50, 70 and
100 respectively. After that, the default data of the color
temperature to be adjusted is set.
4. Warm up time
Warm up for 30 minutes before performing any
adjustment.
adjustment.
5. Adjustment for White Balance
a. Display SMPTE at SXGA/60Hz (Input level 0.73V).
b. Set up [SERVICE MODE].
c. Click "INITIAL EEPROM" and again setup Service
b. Set up [SERVICE MODE].
c. Click "INITIAL EEPROM" and again setup Service
Mode.
d. Click "WHITE BALANCE" and then select “AUTO”.
6. 9300K color adjustment
a. Select "9300K" in "COLOR TEMP" and enter.
b. Use a 35% (89Gray) IRE white video field in the
b. Use a 35% (89Gray) IRE white video field in the
primary mode.
c. Adjust "SUB CONTRAST" to secure the color
temperature.
d. Press "MENU" key to exit adjust mode.
7. 6500K color adjustment
a. Select "6500K" in "COLOR TEMP" and enter.
b. Repeat the adjustment procedure as steps b to d at
b. Repeat the adjustment procedure as steps b to d at
9300K.
.
Click on the first or last page to see other SDM-S75A / SDM-S75D / SDM-S75E / SDM-S75F / SDM-S95A / SDM-S95AR / SDM-S95D / SDM-S95DR / SDM-S95E / SDM-S95ER / SDM-S95F / SDM-S95FR service manuals if exist.