Read Sony SDM-S71R Service Manual online
SDM-S71R
US Model
Canadian Model
AEP Model
TFT LCD COLOR COMPUTER DISPLAY
SPECIFICATIONS
SERVICE MANUAL
LCD panel
Panel type: a-Si TFT Active Matrix
Picture size: 17.0 inch
Picture size: 17.0 inch
Input signal format
RGB operating frequency*
Horizontal: 28 – 80 kHz
Vertical: 48 – 75 Hz
Horizontal: 28 – 80 kHz
Vertical: 48 – 75 Hz
Resolution
Horizontal: Max.1280 dots
Vertical: Max.1024 lines
Vertical: Max.1024 lines
Input signal levels
RGB video signal
0.7 Vp-p, 75
Ω, positive
SYNC signal
TTL level, 2.2 k
Ω,
positive or negative
(Separate horizontal and vertical,
or composite sync)
0.3 Vp-p, 75
(Separate horizontal and vertical,
or composite sync)
0.3 Vp-p, 75
Ω, negative
(Sync on green)
Power requirements
100 – 240 V, 50 – 60 Hz,
Max. 1.0 A
Max. 1.0 A
Power consumption
Max. 45 W
Operating temperature 5 – 35
°C
Dimensions (width/height/depth)
Display (upright):
Approx. 423 • 399 • 233 mm
(16 3/4 • 15 3/4 • 9 1/4 inches)
(with stand)
Approx. 423 • 340 • 62 mm
(16 3/4 • 13 1/2 • 2 1/2 inches)
(without stand)
(16 3/4 • 15 3/4 • 9 1/4 inches)
(with stand)
Approx. 423 • 340 • 62 mm
(16 3/4 • 13 1/2 • 2 1/2 inches)
(without stand)
Mass
Approx. 6.0 kg (13 lb 4 oz) (with
stand)
Approx. 4.7 kg (10 lb 6 oz)
(without stand)
stand)
Approx. 4.7 kg (10 lb 6 oz)
(without stand)
Plug & Play
DDC2B
* Recommended horizontal and vertical timing condition
• Horizontal sync width duty should be more than 4.8% of total
horizontal time or 0.8
horizontal time or 0.8
µsec, whichever is larger.
• Horizontal blanking width should be more than 2.5
µsec.
• Vertical blanking width should be more than 450
µsec.
Design and specifications are subject to change without notice.
SDM-S71R(E)
1-1
SECTION 1
DISASSEMBLY
1-1.CABINET ASSEMBLY
1 Four screws
(
(
+PVTP 3x16)
2 Cabinet assembly
3 Chassis assembly,
bezel assembly
bezel assembly
SDM-S71R(E)
1-2
1-2.H MOUNT
2 Screw
(
(
+BVTP 3x8)
2 Screw
(
(
+BVTP 3x8)
3 H board
1 P1
SDM-S71R(E)
1-3
1-3.G MOUNT
1 Two screws
(
(
+PTT 3x4)
1 Three screws
(
(
+PTT 3x4)
1 Two screws
(
(
+PTT 3x4)
1 Screw (+PTT 3x4)
4 Three screws
(
(
+PTTWH 3x6)
2 Rear shield
3 Conector (inlet)
3 CN2
5 G board
3 CN3
3 CN1