Read Sony GDM-FW9011 Service Manual online
1-2
6
Setup
This monitor works with platforms running at horizontal
frequencies between 30 and 121 kHz.
frequencies between 30 and 121 kHz.
Step 1:Connect your monitor to
your computer
Turn off the monitor and computer before connecting.
Notes
ï Do not touch the pins of the video signal cable connector as this might
bend the pins.
ï When connecting the video signal cable, check the alignment of the
connector. Do not force the connector in the wrong way or the pins
might bend.
might bend.
x
x
x
x
Connecting to the HD15 connector
x
x
x
x
Connecting to the five BNC connectors
* Connect the cables from left to right in the following order: Red-Green-
Blue-HD-VD.
Note
Plug & Play (DDC) does not apply to the five BNC connectors. If you
want to use Plug & Play, connect your computer to the connector using
the supplied video signal cable.
want to use Plug & Play, connect your computer to the connector using
the supplied video signal cable.
Step 2:Connect the power cord
With the monitor and computer switched off, first connect the
power cord to the monitor, then connect it to a power outlet.
power cord to the monitor, then connect it to a power outlet.
A
C
IN
R
G
B
H
D
V
D
2
1
video signal cable
(supplied with host computer)
(supplied with host computer)
To a computer with
an HD15 video output
an HD15 video output
to HD15 input
A
C
IN
R
G
B
H
D
V
D
2
1
to R/G/B input
to HD/VD
input
input
Refer to the preceding
examples to connect to your
computer.
examples to connect to your
computer.
video signal cable
(not supplied)
(not supplied)
*
A
C
IN
R
G
B
H
D
V
D
2
1
to AC IN
to a power outlet
power cord
7
GB
Step 3: Turn on the monitor and
computer
First turn on the monitor, then turn on the computer.
The installation of your monitor is complete.
If necessary, use the monitorís controls to adjust the picture.
If necessary, use the monitorís controls to adjust the picture.
If no picture appears on your screen
ï Check that the monitor is correctly connected to the computer.
ï If NO INPUT SIGNAL appears on the screen, try changing the
ï If NO INPUT SIGNAL appears on the screen, try changing the
input signal (page 8), and confirm that your computerís graphic
board is completely seated in the correct bus slot.
board is completely seated in the correct bus slot.
ï If you are replacing an old monitor with this model and OUT
OF SCAN RANGE appears on the screen, reconnect the old
monitor. Then adjust the computerís graphic board so that the
horizontal frequency is between 30 ñ 121 kHz, and the vertical
frequency is between 48 ñ 160 Hz.
monitor. Then adjust the computerís graphic board so that the
horizontal frequency is between 30 ñ 121 kHz, and the vertical
frequency is between 48 ñ 160 Hz.
For more information about the on-screen messages, see ìT rouble
symptoms and remediesî on page 17.
symptoms and remediesî on page 17.
Connecting Universal Serial Bus
(USB) compliant peripherals
(USB) compliant peripherals
Your monitor has one upstream and four downstream USB
connectors. They provide a fast and easy way to connect USB
compliant peripheral devices (such as keyboards, mice, printers
and scanners) to your computer using a standardized USB cable.
To use your monitor as a hub for your peripheral devices, connect
the USBs as illustrated below.
connectors. They provide a fast and easy way to connect USB
compliant peripheral devices (such as keyboards, mice, printers
and scanners) to your computer using a standardized USB cable.
To use your monitor as a hub for your peripheral devices, connect
the USBs as illustrated below.
1
Turn on the monitor and computer.
2
Connect your computer to the square upstream
connector using the USB cable (not supplied).
3
Connect your USB compliant peripheral devices to
the rectangular downstream
the rectangular downstream
USB connectors.
Notes
ï Not all computers and/or operating systems support USB
configurations. Check your computerís instruction manual to see if you
can connect USB devices.
can connect USB devices.
ï In most cases, USB driver software needs to be installed on the host
computer. Refer to the peripheral deviceís instruction manual for
further details.
further details.
ï The monitor functions as a USB hub as long as the monitor is either
ì onî or in power saving mode.
ï If you connect a keyboard or mouse to the USB connectors and then
boot your computer for the first time, the peripheral devices may not
function. First connect the keyboard and mouse directly to the
computer and set up the USB compliant devices. Then connect them to
this monitor.
function. First connect the keyboard and mouse directly to the
computer and set up the USB compliant devices. Then connect them to
this monitor.
to USB compliant
peripheral devices
peripheral devices
to a USB compliant
computer
computer
Click on the first or last page to see other GDM-FW9011 service manuals if exist.