Read Sony GDM-FW900 Service Manual online
1-2
6
Setup
Before using your monitor, check that the following accessories
are included in your carton:
• Power cord (1)
• Video signal cable (1)
• USB cable (1)
• Exclusive Power Mac G3/G4 adapter (1)
• Warranty card (1)
• Notes on cleaning the screen’s surface (1)
• This instruction manual (1)
are included in your carton:
• Power cord (1)
• Video signal cable (1)
• USB cable (1)
• Exclusive Power Mac G3/G4 adapter (1)
• Warranty card (1)
• Notes on cleaning the screen’s surface (1)
• This instruction manual (1)
Step 1: Connect your monitor to
your computer
Turn off the monitor and computer before connecting.
Notes
• Do not touch the pins of the video signal cable connector as this might
bend the pins.
• When connecting the video signal cable, check the alignment of the
connector. Do not force the connector in the wrong way or the pins
might bend.
might bend.
x
Connecting to an IBM PC/AT or compatible
computer
computer
x
Connecting to a Macintosh computer
* Connect the supplied adapter to the computer before connecting the
cable. This adapter is compatible only with Power Mac G3/G4
computers that have 3 rows of pins. If you connect to the other version
of Macintosh series computer that has 2 rows of pins, you will need a
different adapter (not supplied).
computers that have 3 rows of pins. If you connect to the other version
of Macintosh series computer that has 2 rows of pins, you will need a
different adapter (not supplied).
x
Connecting to the five BNC connectors
* Connect the cables from left to right in the following order: Red-Green-
Blue-HD-VD.
Note
Plug & Play (DDC) does not apply to the five BNC connectors. If you
want to use Plug & Play, connect your computer to the connector using
the supplied video signal cable.
want to use Plug & Play, connect your computer to the connector using
the supplied video signal cable.
AC IN
R
G
B
HD
VD
2
1
video signal cable
(supplied)
(supplied)
to video output
IBM PC/AT or compatible
computer
computer
to HD15 input
AC IN
R
G
B
HD
VD
2
1
Use the supplied exclusive Power Mac G3/G4 adapter.
to HD15 input
exclusive Power
Mac G3/G4 adapter
(supplied)
Mac G3/G4 adapter
(supplied)
*
Power Mac G3/G4
to video
output
output
video signal cable
(supplied)
(supplied)
AC IN
R
G
B
HD
VD
2
1
to R/G/B input
to HD/VD
input
input
Refer to the preceding
examples to connect to your
computer.
examples to connect to your
computer.
video signal cable
(SMF-400, not supplied)
(SMF-400, not supplied)
*
7
GB
Step 2: Connect the power cord
With the monitor and computer switched off, first connect the
power cord to the monitor, then connect it to a power outlet.
power cord to the monitor, then connect it to a power outlet.
Step 3: Turn on the monitor and
computer
First turn on the monitor, then turn on the computer.
The installation of your monitor is complete.
If necessary, use the monitor’s controls to adjust the picture.
If necessary, use the monitor’s controls to adjust the picture.
If no picture appears on your screen
• Check that the monitor is correctly connected to the computer.
• If NO INPUT SIGNAL appears on the screen, try changing the
• If NO INPUT SIGNAL appears on the screen, try changing the
input signal (page 9), and confirm that your computer’s graphic
board is completely seated in the correct bus slot.
board is completely seated in the correct bus slot.
• If you are replacing an old monitor with this model and OUT
OF SCAN RANGE appears on the screen, reconnect the old
monitor. Then adjust the computer’s graphic board so that the
horizontal frequency is between 30 – 121 kHz, and the vertical
frequency is between 48 – 160 Hz.
monitor. Then adjust the computer’s graphic board so that the
horizontal frequency is between 30 – 121 kHz, and the vertical
frequency is between 48 – 160 Hz.
For more information about the on-screen messages, see “Trouble
symptoms and remedies” on page 18.
symptoms and remedies” on page 18.
Setup on various OS (Operating System)
This monitor complies with the “DDC” Plug & Play standard and
automatically detects all the monitor’s information. No specific driver
needs to be installed to the computer.
If you connect the monitor to your PC, and then boot your PC for the first
time, the setup Wizard may be displayed on the screen. Click on “Next”
several times according to the instructions from the Wizard until the Plug
& Play Monitor is automatically selected so that you can use this monitor.
If your PC/graphic board has difficulty communicating with this monitor,
download the specific driver by accessing the web site of the OS’s
manufacturer.
automatically detects all the monitor’s information. No specific driver
needs to be installed to the computer.
If you connect the monitor to your PC, and then boot your PC for the first
time, the setup Wizard may be displayed on the screen. Click on “Next”
several times according to the instructions from the Wizard until the Plug
& Play Monitor is automatically selected so that you can use this monitor.
If your PC/graphic board has difficulty communicating with this monitor,
download the specific driver by accessing the web site of the OS’s
manufacturer.
For customers using Windows NT4.0
Monitor setup in Windows NT4.0 does not use the display driver. Refer
to the Windows NT4.0 instruction manual for further details on adjusting
the resolution, refresh rate, and number of colors.
to the Windows NT4.0 instruction manual for further details on adjusting
the resolution, refresh rate, and number of colors.
AC IN
R
G
B
HD
VD
2
1
to AC IN
to a power outlet
power cord (supplied)
Click on the first or last page to see other GDM-FW900 service manuals if exist.