Read Sony CPD-E500 / CPD-E500E Service Manual online
1-2
6
Setup
Before using your monitor, check that the following accessories
are included in your carton:
• Power cord (1)
• Macintosh adapter (for beige system) (1)
• Setup Disk (1)
• Warranty card (1)
• Notes on cleaning the screen’s surface (1)
• This instruction manual (1)
are included in your carton:
• Power cord (1)
• Macintosh adapter (for beige system) (1)
• Setup Disk (1)
• Warranty card (1)
• Notes on cleaning the screen’s surface (1)
• This instruction manual (1)
Step 1: Connect your monitor to
your computer
Turn off the monitor and computer before connecting.
Note
Do not touch the pins of the video signal cable connector as this might
bend the pins.
bend the pins.
x
Connecting to an IBM PC/AT or compatible
computer
computer
x
Connecting to a Macintosh or compatible
computer
computer
* Connect the supplied Macintosh adapter to the computer before
connecting the cable.
This adapter is compatible with Macintosh LC, Performa, Quadra,
Power Macintosh, and Power Macintosh G3 series computers that have
two rows of pins. If you are connecting to the other version of Power
Macintosh G3 series with three rows of pins or models other than those
stated above, you will need a different adapter (not supplied).
This adapter is compatible with Macintosh LC, Performa, Quadra,
Power Macintosh, and Power Macintosh G3 series computers that have
two rows of pins. If you are connecting to the other version of Power
Macintosh G3 series with three rows of pins or models other than those
stated above, you will need a different adapter (not supplied).
Step 2: Connect the power cord
With the monitor and computer switched off, first connect the
power cord to the monitor, then connect it to a power outlet.
power cord to the monitor, then connect it to a power outlet.
AC IN
to video output
IBM PC/AT or compatible
computer
computer
AC IN
Macintosh adapter (for beige system)
(supplied)
(supplied)
*
Macintosh or
compatible computer
compatible computer
to video
output
output
AC IN
to AC IN
to a power outlet
power cord (supplied)
7
US
Step 3: Turn on the monitor and
computer
First turn on the monitor, then turn on the computer.
The installation of your monitor is complete.
If necessary, use the monitor’s controls to adjust the picture.
If necessary, use the monitor’s controls to adjust the picture.
If no picture appears on your screen
• Check that the monitor is correctly connected to the computer.
• If NO INPUT SIGNAL appears on the screen, confirm that
• If NO INPUT SIGNAL appears on the screen, confirm that
your computer’s graphic board is completely seated in the
correct bus slot.
correct bus slot.
• If you are replacing an old monitor with this model and OUT
OF SCAN RANGE appears on the screen, reconnect the old
monitor. Then adjust the computer’s graphic board so that the
horizontal frequency is between 30 – 109 kHz, and the vertical
frequency is between 48 – 160 Hz.
monitor. Then adjust the computer’s graphic board so that the
horizontal frequency is between 30 – 109 kHz, and the vertical
frequency is between 48 – 160 Hz.
For more information about the on-screen messages, see “Trouble
symptoms and remedies” on page 16.
symptoms and remedies” on page 16.
For customers using Windows 95/98
To maximize the potential of your monitor, install the new model
information file from the supplied Setup Disk onto your PC.
This monitor complies with the “VESA DDC” Plug & Play standard. If
your PC/graphics board complies with DDC, select “Plug & Play Monitor
(VESA DDC)” or this monitor’s model name as the monitor type in the
“Control Panel” of Windows 95/98. If your PC/graphics board has
difficulty communicating with this monitor, load the Setup Disk and
select this monitor’s model name as the monitor type.
information file from the supplied Setup Disk onto your PC.
This monitor complies with the “VESA DDC” Plug & Play standard. If
your PC/graphics board complies with DDC, select “Plug & Play Monitor
(VESA DDC)” or this monitor’s model name as the monitor type in the
“Control Panel” of Windows 95/98. If your PC/graphics board has
difficulty communicating with this monitor, load the Setup Disk and
select this monitor’s model name as the monitor type.
For customers using Windows NT4.0
Monitor setup in Windows NT4.0 is different from Windows 95/98 and
does not involve the selection of monitor type. Refer to the Windows
NT4.0 instruction manual for further details on adjusting the resolution,
refresh rate, and number of colors.
does not involve the selection of monitor type. Refer to the Windows
NT4.0 instruction manual for further details on adjusting the resolution,
refresh rate, and number of colors.
Selecting the on-screen menu
language (LANG)
language (LANG)
English, French, German, Spanish, Italian, Dutch, Swedish,
Russian and Japanese versions of the on-screen menus are
available. The default setting is English.
Russian and Japanese versions of the on-screen menus are
available. The default setting is English.
1
Press the center of the control button.
See page 9 for more information on using the control button.
2
Move the control button to highlight
LANG and
press the center of the control button again.
3
Move the control button
m
/
M
to select a language.
• ENGLISH
• FRANÇAIS: French
• DEUTSCH: German
• ESPAÑOL: Spanish
• ITALIANO: Italian
• NEDERLANDS: Dutch
• SVENSKA: Swedish
•
• FRANÇAIS: French
• DEUTSCH: German
• ESPAÑOL: Spanish
• ITALIANO: Italian
• NEDERLANDS: Dutch
• SVENSKA: Swedish
•
: Russian
•
: Japanese
To close the menu
Press the center of the control button once to return to the main MENU,
and twice to return to normal viewing. If no buttons are pressed, the menu
closes automatically after about 30 seconds.
and twice to return to normal viewing. If no buttons are pressed, the menu
closes automatically after about 30 seconds.
To reset to English
Press the RESET button while the LANGUAGE menu is displayed on the
screen.
screen.
MENU
MENU
MENU
EXIT
CENTER
SIZE
GEOM
SCREEN
COLOR
LANG
CONV
OPTION
OK
MENU
ENGL I SH
FRANÇA I S
DEUT SCH
ESPAÑOL
FRANÇA I S
DEUT SCH
ESPAÑOL
I T A L I ANO
NEDER L ANDS
SVENSKA
SVENSKA
L ANGUAGE
Click on the first or last page to see other CPD-E500 / CPD-E500E service manuals if exist.