Read Sony CPD-E400 / CPD-E400E / CPD-E400P Service Manual online
1-2
6
Setup
Before using your monitor, check that the following accessories
are included in your carton:
• Power cord
• Current G3 adapter (for beige system) (1)
• Setup Disk (1)
• Warranty card
• Notes on cleaning the screen’s surface
• This instruction manual
are included in your carton:
• Power cord
• Current G3 adapter (for beige system) (1)
• Setup Disk (1)
• Warranty card
• Notes on cleaning the screen’s surface
• This instruction manual
Step 1: Connect your monitor to
your computer
Turn off the monitor and computer before connecting.
Note
Do not touch the pins of the video signal cable connector as this might
bend the pins.
bend the pins.
x
Connecting to an IBM PC/AT or compatible
computer
computer
x
Connecting to a Macintosh or compatible
computer
computer
* Connect the supplied Macintosh adapter to the computer before
connecting the cable.
This adapter is compatible with Macintosh LC, Performa, Quadra,
Power Macintosh, and Power Macintosh G3 series computers that have
two rows of pins. If you are connecting to the other version of Power
Macintosh G3 series with three rows of pins or models other than those
stated above, you will need a different adapter (not supplied).
This adapter is compatible with Macintosh LC, Performa, Quadra,
Power Macintosh, and Power Macintosh G3 series computers that have
two rows of pins. If you are connecting to the other version of Power
Macintosh G3 series with three rows of pins or models other than those
stated above, you will need a different adapter (not supplied).
AC IN
1
(HD15)
IBM PC/AT or
compatible computer
compatible computer
to video output
AC IN
1
(HD15)
Current G3 adapter (for beige system)
(supplied)
(supplied)
*
Macintosh or
compatible computer
compatible computer
to video
output
output
7
US
Step 2: Connect the power cord
With the monitor and computer switched off, first connect the
power cord to the monitor, then connect it to a power outlet.
power cord to the monitor, then connect it to a power outlet.
Step 3: Turn on the monitor and
computer
First turn on the monitor, then turn on the computer.
The installation of your monitor is complete.
If necessary, use the monitor’s controls to adjust the picture.
If necessary, use the monitor’s controls to adjust the picture.
If no picture appears on your screen
• Check that the monitor is correctly connected to the computer.
• If NO INPUT SIGNAL appears on the screen, confirm that the
• If NO INPUT SIGNAL appears on the screen, confirm that the
video signal cable is properly connected and all plugs are firmly
seated in their sockets.
seated in their sockets.
• If MONITOR IS IN POWER SAVE MODE appeared on the
screen, try pressing any key on the computer keyboard.
• If you are replacing an old monitor with this model and OUT
OF SCAN RANGE appears on the screen, reconnect the old
monitor. Then adjust the computer’s graphic board so that the
horizontal frequency is between 30 – 96 kHz, and the vertical
frequency is between 48 – 120 Hz.
monitor. Then adjust the computer’s graphic board so that the
horizontal frequency is between 30 – 96 kHz, and the vertical
frequency is between 48 – 120 Hz.
For more information about the on-screen messages, see “Trouble
symptoms and remedies” on page 16.
symptoms and remedies” on page 16.
Setup on various OS (Operating System)
This monitor complies with the “DDC” Plug & Play standard and
automatically detects all the monitor’s information with the Windows
Plug & Play function. No specific driver needs to be installed to the
computer.
If you connect the monitor to your PC, and then boot your PC for the first
time, the setup Wizard may be displayed on the screen. Click on “Next”
several times according to the instructions from the Wizard until the Plug
& Play Monitor is automatically selected so that you can use this monitor.
If your PC/graphics board has difficulty communicating with this
monitor, load the supplied Setup Disk. Refer to the “Read Me” file on the
Disk about the procedure to install. You can also download the
information by accessing the web site of the graphics board’s
manufacturer.
automatically detects all the monitor’s information with the Windows
Plug & Play function. No specific driver needs to be installed to the
computer.
If you connect the monitor to your PC, and then boot your PC for the first
time, the setup Wizard may be displayed on the screen. Click on “Next”
several times according to the instructions from the Wizard until the Plug
& Play Monitor is automatically selected so that you can use this monitor.
If your PC/graphics board has difficulty communicating with this
monitor, load the supplied Setup Disk. Refer to the “Read Me” file on the
Disk about the procedure to install. You can also download the
information by accessing the web site of the graphics board’s
manufacturer.
For customers using Windows NT4.0
Monitor setup in Windows NT4.0 does not use the display driver. Refer
to the Windows NT4.0 instruction manual for further details on adjusting
the resolution, refresh rate, and number of colors.
to the Windows NT4.0 instruction manual for further details on adjusting
the resolution, refresh rate, and number of colors.
AC IN
1
(HD15)
to AC IN
to a power outlet
power cord (supplied)
Click on the first or last page to see other CPD-E400 / CPD-E400E / CPD-E400P service manuals if exist.