CPD-E200E - Sony Monitor Service Manual (repair manual). Page 6

1-2

6

Before using your monitor, check that the following accessories 
are included in your carton:
• Power cord (1)
• Windows Monitor Information Disk (1)
• Warranty card (1)
• Notes on cleaning the screen’s surface (1)
• This instruction manual (1)

Turn off the monitor and computer before connecting.

Do not touch the pins of the video cable connector as this might bend the 
pins.

x

x

With the monitor and computer switched off, first connect the 
power cord to the monitor, then connect it to a power outlet.

IBM PC/AT or 
compatible computer

to video output

You will need a Macintosh adapter (not supplied).

Macintosh adapter (not supplied)

Macintosh or compatible computer

to video output

to AC IN

to a power outlet

power cord (supplied)

7

First turn on the monitor, then turn on the computer.

The installation of your monitor is complete.
If necessary, use the monitor’s controls to adjust the picture.

• Check that the monitor is correctly connected to the computer.
• If NO INPUT SIGNAL appears on the screen, confirm that the 

video signal cable is properly connected and all plugs are firmly 
seated in their sockets.

• If MONITOR IS IN POWER SAVE MODE appeared on the 

screen, try pressing any key on the computer keyboard.

• If you are replacing an old monitor with this model and OUT 

OF SCAN RANGE appears on the screen, reconnect the old 
monitor. Then adjust the computer’s graphic board so that the 
horizontal frequency is between 30 – 85 kHz, and the vertical 
frequency is between 48 – 120 Hz.

For more information about the on-screen messages, see “Trouble 
symptoms and remedies” on page 14.

To maximize the potential of your monitor, install the new model 
information file from the supplied Windows Monitor Information Disk 
onto your PC.
This monitor complies with the “VESA DDC” Plug & Play standard. If 
your PC/graphics board complies with DDC, select “Plug & Play Monitor 
(VESA DDC)” or this monitor’s model name as the monitor type in the 
“Control Panel” of Windows 95/98. If your PC/graphics board has 
difficulty communicating with this monitor, load the Windows Monitor 
Information Disk and select this monitor’s model name as the monitor 
type.

Monitor setup in Windows NT4.0 is different from Windows 95/98 and 
does not involve the selection of monitor type. Refer to the Windows 
NT4.0 instruction manual for further details on adjusting the resolution, 
refresh rate, and number of colors.

Adjust the monitor’s resolution and color number by referring to your 
computer’s instruction manual. The color number may vary according to 
your computer or video board. The color palette setting and the actual 
number of colors are as follows:
• High Color (16 bit) 

t 65,536 colors

• True Color (24 bit) 

t about 16.77 million colors

In true color mode (24 bit), speed may be slower.

English, French, German, Spanish, Italian, Dutch, Swedish, 
Russian and Japanese versions of the on-screen menus are 
available. The default setting is English.

See page 9 for more information on using the control button.

m

M

• ENGLISH
• FRANÇAIS: French
• DEUTSCH: German
• ESPAÑOL: Spanish
• ITALIANO: Italian
• NEDERLANDS: Dutch
• SVENSKA: Swedish
•

: Russian

•

: Japanese 

Press the center of the control button once to return to the main MENU, 
and twice to return to normal viewing. If no buttons are pressed, the menu 
closes automatically after about 30 seconds.

Press the RESET button while the LANGUAGE menu is displayed on the 
screen.

MENU

MENU

EXIT

CENTER

SIZE

GEOM

COLOR

LANG

HELP

CONV

OPTION

OK

ENGL I SH
FRANÇA I S
DEUT SCH
ESPAÑOL

I T A L I ANO

NEDER L ANDS
SVENSKA

L ANGUAGE