DVP-S350 - Sony DVD Service Manual (repair manual)

dvp-s350 service manual
Model
DVP-S350
Pages
89
Size
42.32 MB
Type
PDF
Document
Service Manual
Brand
Device
DVD
File
dvp-s350.pdf
Date

Read Sony DVP-S350 Service Manual online

SERVICE MANUAL
US Model
CD/DVD PLAYER
SPECIFICATIONS
DVP-S350
RMT-D116A
– 2 –
WARNING!!
WHEN  SERVICING,  DO  NOT  APPROACH  THE  LASER
EXIT  WITH  THE  EYE  TOO  CLOSELY.  IN  CASE  IT  IS
NECESSARY  TO  CONFIRM  LASER  BEAM  EMISSION,
BE  SURE  TO  OBSERVE  FROM  A  DISTANCE  OF
MORE   THAN   25  cm  FROM  THE  SURFACE  OF  THE
OBJECTIVE  LENS  ON  THE  OPTICAL  PICK-UP  BLOCK.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous ra-
diation exposure.
SAFETY-RELATED  COMPONENT  WARNING!!
COMPONENTS  IDENTIFIED  BY  MARK  
0
  OR  DOTTED
LINE  WITH  MARK  
0
  ON  THE  SCHEMATIC  DIAGRAMS
AND  IN  THE  PARTS  LIST  ARE  CRITICAL  TO  SAFE
OPERATION.  REPLACE  THESE  COMPONENTS  WITH
SONY  PARTS  WHOSE  PART  NUMBERS  APPEAR  AS
SHOWN  IN  THIS  MANUAL  OR  IN  SUPPLEMENTS  PUB-
LISHED  BY  SONY.
CAUTION:
The use of optical instrument with this product will increase eye
hazard.
Fig. A.
Using an AC voltmeter to check AC leakage.
1.5 k
0.15 
µ
F
AC
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground
and from all exposed metal parts to any exposed metal part having
a return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A.  Follow the manufacturers' instructions to use these
instruments.
2. A battery-operated AC milliammeter.  The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter.  The “limit” indica-
tion is 0.75V, so analog meters must have an accurate low-
voltage scale.  The Simpson 250 and Sanwa SH-63Trd are ex-
amples of a passive VOM that is suitable.  Nearly all battery
operated digital multimeters that have a 2V AC range are suit-
able.  (See Fig. A)
1. Check the area of your repair for unsoldered or poorly-sol-
dered connections.  Check the entire board surface for solder
splashes and bridges.
2. Check the interboard wiring to ensure that no wires are
“pinched” or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transis-
tors, that were installed during a previous repair.  Point them
out to the customer and recommend their replacement.
4. Look for parts which, though functioning, show obvious signs
of deterioration.  Point them out to the customer and recom-
mend their replacement.
5. Check the line cord for cracks and abrasion. Recommend the
replacement of any such line cord to the customer.
6. Check the B+ voltage to see it is at the values specified.
7. Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer:
– 3 –
TABLE  OF  CONTENTS
Section
Title
Page
Section
Title
Page
Service Note ............................................................................ 4
1.
GENERAL
Getting Started .............................................................. 1-1
Playing Discs ................................................................. 1-4
Using Various Functions with the Control Menu ........... 1-6
Settings and Adjustments ............................................. 1-10
2.
DISASSEMBLY
2-1.
Case Removal ............................................................... 2-1
2-2.
Rear Panel Removal ..................................................... 2-1
2-3.
Tray Cover Removal ...................................................... 2-1
2-4.
Front Panel Removal ..................................................... 2-1
2-5.
Power Block Removal ................................................... 2-2
2-6.
Mechanism Deck Removal............................................ 2-2
2-7.
Tray Removal ................................................................. 2-2
2-8.
Optical Pick-up Removal ............................................... 2-2
2-9.
Belt, MB-86 Board, Loading Motor (M001),
MS-48 Board Removal .................................................. 2-3
2-10. AI-022 Board Removal .................................................. 2-3
2-11. Internal Views ................................................................ 2-4
2-12. Circuit Boards Location ................................................. 2-5
3.
BLOCK DIAGRAMS
3-1.
Overall Block Diagram ................................................... 3-1
3-2.
RF/Servo Block Diagram ............................................... 3-3
3-3.
Signal Processor Block Diagram .................................. 3-5
3-4.
Video/Audio Block Diagram .......................................... 3-7
3-5.
System Control Block Diagram ..................................... 3-9
3-6.
Interface Control Block Diagram ................................... 3-11
3-7.
Power Block Diagram .................................................... 3-13
4.
PRINTED WIRING BOARDS AND SCHEMATIC
DIAGRAMS
4-1.
Frame Schematic Diagram ............................................ 4-3
4-2.
Printed Wiring Boards and Schematic Diagrams ......... 4-5
MS-48 Printed Wiring Board and
Schematic Diagram ....................................................... 4-5
MB-86 Printed Wiring Board ......................................... 4-7
MB-86 (RF AMP, SERVO) Schematic Diagram ............ 4-11
MB-86 (ARP) Schematic Diagram ................................ 4-13
MB-86 (AV DECODER) Schematic Diagram ................ 4-15
MB-86 (SDRAM) Schematic Diagram .......................... 4-17
MB-86 (DRIVE) Schematic Diagram ............................ 4-19
MB-86 (SERVO DSP) Schematic Diagram ................... 4-21
MB-86 (SYSTEM CONTROL)
Schematic Diagram ....................................................... 4-23
MB-86 (MEMORY, CLOCK GENERATOR)
Schematic Diagram ....................................................... 4-25
AI-022 Printed Wiring Board ......................................... 4-27
AI-022 (VIDEO BUFFER) Schematic Diagram ............. 4-29
AI-022 (D/A CONVERTER, DSP)
Schematic Diagram ....................................................... 4-31
AI-022 (POWER SUPPLY) Schematic Diagram ........... 4-33
AI-022 (IF CON) Schematic Diagram ........................... 4-35
FR-177, FL-118 Printed Wiring Boards and
Schematic Diagrams ..................................................... 4-37
HS16S9U Printed Wiring Board .................................... 4-39
HS16S9U Schematic Diagram ...................................... 4-41
5.
IC PIN FUNCTION DESCRIPTION
5-1.
System Control Pin Function
(MB-86 Board IC102) .................................................... 5-1
6.
TEST MODE
6-1.
General Description ...................................................... 6-1
6-2.
Starting Test Mode ........................................................ 6-1
6-3.
Syscon Diagnosis .......................................................... 6-1
6-4.
Drive Auto Adjustment .................................................. 6-5
6-5.
Drive Manual Operation ................................................ 6-7
6-6.
Mecha Aging ................................................................. 6-9
6-7.
Emergency History ........................................................ 6-9
6-8.
Version Information ....................................................... 6-10
6-9.
Video Level Adjustment ................................................ 6-10
6-10. If Con Self Diagnostic Function .................................... 6-11
7.
ELECTRICAL ADJUSTMENT
7-1.
Power Supply Adjustment ............................................. 7-1
1.
Power Supply Check ..................................................... 7-1
7-2.
Adjustment of Video System ......................................... 7-2
1.
Video Level Adjustment ................................................ 7-2
2.
S-terminal Output Check ............................................... 7-2
3.
Checking Component Video Output B-Y ...................... 7-2
4.
Checking Component Video Output R-Y ...................... 7-2
5.
Checking Component Video Output Y .......................... 7-3
6.
Checking S Video Output S-C ....................................... 7-3
7-3.
Adjustment Related Par ts Arrangement ....................... 7-4
8.
REPAIR PARTS LIST
8-1.
Exploded Views ............................................................. 8-1
8-1-1. Case Assembly ........................................................ 8-1
8-1-2. Chassis Assembly .................................................... 8-2
8-1-3. Mechanism Deck Section ........................................ 8-3
8-2.
Electrical Parts List ....................................................... 8-4
– 4 –
SERVICE NOTE
1.
DISASSEMBLY
• This set can be disassembled in the order shown below.
Set
Case
(Page 2-1)
Power 
Block
(Page 2-2)
AI-022 Board
(Page 2-3)
Mechanism
Deck
(Page 2-2)
Front Panel
(Page 2-1)
Rear Panel
(Page 2-1)
Tray Cover
(Page 2-1)
Optical Pick-up
(Page 2-2)
MB-86 Board
(Page 2-3)
Belt
(Page 2-3)
Loading Motor (M001),
MS-48 Board
(Page 2-3)
Tray
(Page 2-2)
Page of 89
Display

Download Sony DVP-S350 Service Manual (Repair Manual)

Here you can read online and download Sony DVP-S350 Service Manual in PDF. DVP-S350 service manual will guide through the process and help you recover, restore, fix, disassemble and repair Sony DVP-S350 DVD. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.