DVP-NS72HP, DVP-NS77H, DVP-NS77HP, DVP-NS78H, DVP-NS78HP - Sony DVD Service Manual (repair manual). Page 10

1-5

Select one of the following patterns 

A or B according to the input jack on your TV monitor, 

projector, or audio component such as an AV amplifier (receiver). This will enable you to listen 
to sound.

z Hint
For correct speaker location, see the operating instructions supplied with the connected components.

L

C E N T E R

VIDEO

AUDIO

INPUT

L

R

HDMI cord (not supplied)

(red)

TV, projector, or 
audio component

Audio/video 
cord (supplied)

: Signal flow

to DIGITAL OUT (COAXIAL)/HDMI OUT

to LINE OUT L/R (AUDIO)

Rear (L)

CD/DVD player

(white)

(yellow)*

(yellow)*

(white)

(red)

[Speakers]

Front (L)

[Speakers]

Rear (R)

Front (R)

Subwoofer

Centre

Coaxial digital cord 
(not supplied)

to coaxial/HDMI 
digital input

Audio component 
with a decoder

* The yellow plug is used for video signals (page 15).

,continued

A Audio L/R input jacks

This connection will use your TV’s or audio 
component’s two speakers for sound.

B Digital audio input jack

If your audio component has a Dolby*

1

Digital, DTS*

2

, or MPEG audio decoder and 

a digital input jack, use this connection. You 
can enjoy Dolby Digital (5.1ch) and DTS 
(5.1ch) surround effect.
If you connect to a Sony audio component 
that is compatible with the HDMI 
CONTROL function, refer to the operating 
instructions supplied with the audio 
component.

*1

Manufactured under license from Dolby 
Laboratories.
Dolby, Pro Logic, and the double-D symbol are 
trademarks of Dolby Laboratories.

*2

“DTS” and “DTS Digital Out” are registered 
trademarks of DTS, Inc.

• After you have completed the connection, be sure 

to set “DOLBY DIGITAL” to “DOLBY 
DIGITAL” and “DTS” to “ON” in Quick Setup 
(page 23). If your audio component has an MPEG 
audio decoder function, set “MPEG” to “MPEG” 
in Audio Setup (page 63). Otherwise, no sound or 
a loud noise will come from your speakers.

• When you connect an audio component that 

conforms to the 96 kHz sampling frequency, set 
“48kHz/96kHz PCM” in “AUDIO SETUP” to 
“96kHz/24bit” (page 63).

• The TVS effects of this player cannot be used 

with this connection.

• When you connect the player to an audio 

component using an HDMI cord, you will need to 
do one of the following:

– Connect the audio component to the TV with the 

HDMI cord.

– Connect the player to the TV with a video cord 

other than HDMI cord (component video cord or 
audio/video cord).

• When connecting to the HDMI OUT jack, 

carefully align the HDMI connector with the jack. 
Do not bend and apply pressure to the HDMI 
cord.

Plug the player and TV mains lead (power cord) into a mains.

You can control the player using the supplied remote. Insert two R6 (size AA) batteries by 
matching the 

3 and # ends on the batteries to the markings inside the compartment. When 

using the remote, point it at the remote sensor 

 on the player.

• Do not leave the remote in an extremely hot or humid place.
• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct light from the sun or a lighting apparatus. Doing so may cause a 

malfunction.

• If you do not use the remote for an extended period of time, remove the batteries to avoid possible damage 

from battery leakage and corrosion.

,continued

You can control the sound level, input source, 
and power switch of your Sony TV with the 
supplied remote.

You can control your TV using the buttons 
below.

Depending on the connected unit, you may not be 
able to control your TV using all or some of the 
buttons on the supplied remote.

You can control the sound level, input source, 
and power switch of non-Sony TVs as well.
If your TV is listed in the table below, set the 
appropriate manufacturer’s code.

[/1, press the 

[/1.

Code numbers of controllable TVs
If more than one code number is listed, try 
entering them one at a time until you find the 
one that works with your TV.

• When you replace the batteries of the remote, the 

code number you have set may be reset to the 
default setting. Set the appropriate code number 
again.

• Depending on the connected unit, you may not be 

able to control your TV using all or some of the 
buttons on the supplied remote.

TV 

[/1

Turn the TV on or off

2 (volume) +/– Adjust the volume of the TV
t (TV/video)

Switch the TV’s input source 
between the TV and other 
input sources

TV

2 +/–
t

Number 
buttons

Sony

01 (default)

Aiwa

01 (default)

Grundig

11

Hitachi

24

JVC

33

LG

06

Loewe

06

Panasonic

17, 49

Philips

06, 08

Samsung

06, 71

Sanyo

25

Sharp

29

Thomson

43

Toshiba

38