Read Sony DVP-NS611HP / DVP-NS710H / DVP-NS710HP / DVP-NS717HP / DVP-NS718H / DVP-NS718HP / DVP-NS728H / DVP-NS728HP Service Manual online
1-3
DVP-NS611HP/NS710H/NS710HP/NS717HP/NS718H/NS718HP/NS728H/NS728HP
12
Step 2: Connecting to Your Audio Component
Select one of the following patterns
A or B, according to the input jack on your TV monitor,
projector, or audio component such as an AV amplifier (receiver).
This will enable you to listen to sound.
This will enable you to listen to sound.
z
For correct speaker location, see the operating instructions supplied with the connected components.
For correct speaker location, see the operating instructions supplied with the connected components.
B
VIDEO
AUDIO
INPUT
L
R
A
Audio component
with a decoder
with a decoder
(red)
TV, projector, or
audio component
audio component
Audio/video
cable (supplied)
cable (supplied)
: Signal flow
to DIGITAL OUT
(COAXIAL)/HDMI OUT
(COAXIAL)/HDMI OUT
to LINE OUT L/R (AUDIO)
Rear (L)
CD/DVD player
(white)
(yellow)
*
(yellow)
*
(white)
(red)
[Speakers]
Front (L)
[Speakers]
Rear (R)
Front (R)
Subwoofer
Centre
* The yellow plug is used for video signals (page 10).
HDMI cord (supplied with
DVP-NS710HP, DVP-NS718HP,
and DVP-NS728HP only)
DVP-NS710HP, DVP-NS718HP,
and DVP-NS728HP only)
Coaxial digital cord
(not supplied)
(not supplied)
to coaxial/HDMI
digital input
digital input
or
13
Ho
oku
oku
ps
a
a
nd
Set
ti
Set
ti
ng
s
s
A
Audio L/R input jacks
This connection will use your TV’s or audio
component’s two speakers for sound.
component’s two speakers for sound.
B
Digital audio input jack
If your audio component has a Dolby*
1
Digital, DTS*
2
, or MPEG audio decoder and
a digital input jack, use this connection. You
can enjoy Dolby Digital (5.1ch), DTS
(5.1ch), and MPEG audio (5.1ch) surround
effect.
If you connect to a Sony audio component
that is compatible with the CONTROL FOR
HDMI function, refer to the operating
instructions supplied with the audio
component.
can enjoy Dolby Digital (5.1ch), DTS
(5.1ch), and MPEG audio (5.1ch) surround
effect.
If you connect to a Sony audio component
that is compatible with the CONTROL FOR
HDMI function, refer to the operating
instructions supplied with the audio
component.
*1
Manufactured under license from Dolby
Laboratories.
Dolby, Pro Logic, and the double-D symbol are
trademarks of Dolby Laboratories.
Laboratories.
Dolby, Pro Logic, and the double-D symbol are
trademarks of Dolby Laboratories.
*2
Manufactured under license under U.S. Patent #:
5,451,942 & other U.S. and worldwide patents
issued & pending. DTS and DTS Digital Out are
registered trademarks and the DTS logos and
Symbol are trademarks of DTS, Inc. © 1996-
2008 DTS, Inc. All Rights Reserved.
5,451,942 & other U.S. and worldwide patents
issued & pending. DTS and DTS Digital Out are
registered trademarks and the DTS logos and
Symbol are trademarks of DTS, Inc. © 1996-
2008 DTS, Inc. All Rights Reserved.
b
• After you have completed the connection, make
• After you have completed the connection, make
the appropriate settings in Quick Setup (page 15).
If your audio component has an MPEG audio
decoder function, set “MPEG” to “MPEG” in
“AUDIO SETUP” (page 37). Otherwise, no
sound or a loud noise will come from your
speakers.
If your audio component has an MPEG audio
decoder function, set “MPEG” to “MPEG” in
“AUDIO SETUP” (page 37). Otherwise, no
sound or a loud noise will come from your
speakers.
• The TVS effects of this player cannot be used
with this connection.
• When you connect the player to an audio
component using an HDMI cord, you will need to
do one of the following:
do one of the following:
– Connect the audio component to the TV with the
HDMI cord.
– Connect the player to the TV with a video cord
other than HDMI cord (component video cord or
audio/video cord).
audio/video cord).
• When connecting to the HDMI OUT jack,
carefully align the HDMI connector with the jack.
Do not bend and apply force to the HDMI cord.
Do not bend and apply force to the HDMI cord.
Step 3: Connecting the
Mains Lead
Mains Lead
Plug the player and TV mains lead (power
cord) into a mains.
cord) into a mains.
Step 4: Preparing the
Remote
Remote
Insert two R6 (size AA) batteries by matching
the
the
3 and # ends on the batteries to the
markings inside the compartment. When
using the remote, point it at the remote sensor
using the remote, point it at the remote sensor
on the player.
b
• Do not leave the remote in an extremely hot or
• Do not leave the remote in an extremely hot or
humid place.
• Do not drop any foreign object into the remote
casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct light
from the sun or a lighting apparatus. Doing so
may cause a malfunction.
may cause a malfunction.
• If you do not use the remote for an extended
period of time, remove the batteries to avoid
possible damage from battery leakage and
corrosion.
possible damage from battery leakage and
corrosion.
,continued
14
Controlling TVs with the remote
You can control the sound level, input source,
and power switch of your Sony TV with the
supplied remote.
and power switch of your Sony TV with the
supplied remote.
Available buttons
Depending on the connected unit, you may
not be able to control your TV using all or
some of the buttons on the supplied remote.
Depending on the connected unit, you may
not be able to control your TV using all or
some of the buttons on the supplied remote.
To control other TVs with the remote
You can control the volume, input source, and
power switch of non-Sony TVs as well.
If your TV is listed in the table below, set the
appropriate manufacturer’s code.
You can control the volume, input source, and
power switch of non-Sony TVs as well.
If your TV is listed in the table below, set the
appropriate manufacturer’s code.
b
When you replace the batteries of the remote, the
code number may be reset to the default setting. Set
the appropriate code number again.
When you replace the batteries of the remote, the
code number may be reset to the default setting. Set
the appropriate code number again.
1
While holding down TV
[/1, press the
number buttons to select your TV’s
manufacturer’s code.
manufacturer’s code.
2
Release TV
[/1.
Code numbers of controllable TVs
If more than one code number is listed, try
entering them one at a time until you find the
one that works with your TV.
If more than one code number is listed, try
entering them one at a time until you find the
one that works with your TV.
◆ For RMT-D187P/RMT-D189P remote
commander only
◆ For RMT-D187A/RMT-D189A remote
commander only
Buttons
Operations
TV
[/1
Turn the TV on or off
2/VOL (volume)
+/–
+/–
Adjust the volume of the
TV
TV
TV
t/TV INPUT
(input select)
Switch the TV’s input
source between the TV and
other input sources
source between the TV and
other input sources
Manufacturer
Code number
Sony
01 (default)
Hitachi
24
JVC
33
LG/Goldstar
76
Panasonic
17, 49
Philips
06, 08, 72
Samsung
71
Sharp
29
Toshiba
38
Manufacturer
Code number
Sony
01 (default)
Hitachi
02
LG/Goldstar/NEC 04
MGA/Mitsubishi 13
Panasonic
19
Philips
21
Pioneer
16
RCA
10
Samsung
20
Sharp
18
Toshiba
07
15
Ho
oku
oku
ps
a
a
nd
Set
ti
Set
ti
ng
s
s
Step 5: Quick Setup
Follow the steps below to make the minimum
number of basic adjustments for using the
player.
To skip an adjustment, press
number of basic adjustments for using the
player.
To skip an adjustment, press
>. To return
to the previous adjustment, press
.. The
on-screen displays differ depending on the
player model. Oceanian model is used for
illustration unless otherwise specified.
player model. Oceanian model is used for
illustration unless otherwise specified.
1
Turn on the TV then press
[
/
1.
2
Switch the input selector on your
TV so that the signal from the
player appears on your TV screen.
player appears on your TV screen.
“Press [ENTER] to run QUICK SETUP”
(press enter to run Quick Setup) appears
at the bottom of the screen. If this
message does not appear, select
“QUICK” (quick) under “SETUP”
(setup) in the Control Menu to run Quick
Setup (page 20).
(press enter to run Quick Setup) appears
at the bottom of the screen. If this
message does not appear, select
“QUICK” (quick) under “SETUP”
(setup) in the Control Menu to run Quick
Setup (page 20).
3
Press ENTER without inserting a
disc.
The Language Setup Display appears.
The available languages differ depending
upon the player model.
The available languages differ depending
upon the player model.
4
Press
X/x to select a language.
The player displays the menu and
subtitles in the selected language.
subtitles in the selected language.
5
Press ENTER.
The Screen Setup Display appears.
6
Press
X/x to select the setting that
matches your TV type.
◆ If you have a wide-screen TV or a 4:3
standard TV with a wide-screen mode
• 16:9 (page 33)
◆ If you have a 4:3 standard TV
• 4:3 LETTER BOX or 4:3 PAN SCAN
standard TV with a wide-screen mode
• 16:9 (page 33)
◆ If you have a 4:3 standard TV
• 4:3 LETTER BOX or 4:3 PAN SCAN
(page 33)
7
Press ENTER.
The Setup Display for selecting the type
of jack used to connect your audio
component appears.
of jack used to connect your audio
component appears.
8
Press
X/x to select the type of jack
(if any) you are using to connect to
an audio component, then press
ENTER.
ENTER.
Select “NO,” if you do not connect an
audio component, then go to step 12.
Select “YES: LINE OUTPUT L/R
(AUDIO),” if you connect an audio
component using an audio cable, then go
to step 12.
Select “YES: DIGITAL OUTPUT,” if
you connect an audio component using a
digital coaxial cable/HDMI cord.
audio component, then go to step 12.
Select “YES: LINE OUTPUT L/R
(AUDIO),” if you connect an audio
component using an audio cable, then go
to step 12.
Select “YES: DIGITAL OUTPUT,” if
you connect an audio component using a
digital coaxial cable/HDMI cord.
LANGUAGE SETUP
OSD:
MENU:
AUDIO:
SUBTITLE:
MENU:
AUDIO:
SUBTITLE:
ITALIANO
ESPAÑOL
NEDERLANDS
DANSK
SVENSKA
FRANÇAIS
ENGLISH
ENGLISH
DEUTSCH
SCREEN SETUP
TV TYPE:
16:9
4:3 LETTER BOX
4:3 PAN SCAN
OFF
COLOR SYSTEM (VIDEO CD):
BACKGROUND:
SCREEN SAVER:
PROGRESSIVE
(COMPONENT OUT ONLY)
:
AUTO
MODE
(PROGRESSIVE)
:
FULL
4:3 OUTPUT:
16:9
YES
NO
Is this player connected to an amplifier
(receiver) ? Select the type of jack you
are using.
(receiver) ? Select the type of jack you
are using.
LINE OUTPUT L/R (AUDIO)
DIGITAL OUTPUT
,continued
Click on the first or last page to see other DVP-NS611HP / DVP-NS710H / DVP-NS710HP / DVP-NS717HP / DVP-NS718H / DVP-NS718HP / DVP-NS728H / DVP-NS728HP service manuals if exist.