Read Sony DVP-K360 Service Manual online
– 2 –
WARNING!!
WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION,
BE SURE TO OBSERVE FROM A DISTANCE OF
MORE THAN 25 cm FROM THE SURFACE OF THE
OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION,
BE SURE TO OBSERVE FROM A DISTANCE OF
MORE THAN 25 cm FROM THE SURFACE OF THE
OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous ra-
diation exposure.
other than those specified herein may result in hazardous ra-
diation exposure.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED
LINE WITH MARK
0
ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
CAUTION:
The use of optical instrument with this product will increase eye
hazard.
hazard.
SAFETY CHECK-OUT
1. Check the area of your repair for unsoldered or poorly-sol-
dered connections. Check the entire board surface for solder
splashes and bridges.
splashes and bridges.
2. Check the interboard wiring to ensure that no wires are
“pinched” or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transis-
tors, that were installed during a previous repair. Point them
out to the customer and recommend their replacement.
out to the customer and recommend their replacement.
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer:
safety checks before releasing the set to the customer:
4. Look for parts which, though functioning, show obvious signs
of deterioration. Point them out to the customer and recom-
mend their replacement.
mend their replacement.
5. Check the B+ voltage to see it is at the values specified.
General
Power requirements
220 to 240 V AC, 50/60 Hz (Singapore)
220 V AC, 50/60 Hz (Hong Kong, Taiwan)
110 V AC, 60 Hz (Chinese)
220 V AC, 50/60 Hz (Hong Kong, Taiwan)
110 V AC, 60 Hz (Chinese)
Power consumption
14 W (Chinese)
13 W (EXCEPT Chinese)
13 W (EXCEPT Chinese)
Dimensions (approx.)
430
×
74
×
264 mm (w/h/d)
incl. projecting parts
Mass (approx.)
2.8 kg
Operating temperature
5 ˚C to 35 ˚C
Operating humidity
25 % to 80 %
Supplied accessories
* The signals from the LINE OUT AUDIO connectors are measured.
When you play PCM sound tracks with a 96 kHz sampling
frequency, the output signals from the DIGITAL OUT OPTICAL
and COAXIAL connectors are converted to 48 kHz (sampling
frequency).
frequency, the output signals from the DIGITAL OUT OPTICAL
and COAXIAL connectors are converted to 48 kHz (sampling
frequency).
Design and specifications are subject to change without notice.
Check that you have the following items:
• Audio/video connecting cord (1)
• Remote commander (remote) RMT-D127E (1)
• R6 (size AA) batteries (2)
• Audio/video connecting cord (1)
• Remote commander (remote) RMT-D127E (1)
• R6 (size AA) batteries (2)
Click on the first or last page to see other DVP-K360 service manuals if exist.