DVP-FX850 - Sony DVD Service Manual (repair manual). Page 14

Read Sony DVP-FX850 Service Manual online

1-10
40
Connecting to an AV amplifier (receiver)
Example 1
To send the playback signal to an AV amplifier (receiver) 
1
Set the LINE SELECT switch on the player’s right side to “OUT.” 
* The yellow plug is used for video signals (page 39).
Example 2
To send the playback signal to an AV amplifier (receiver) 
1
Set the LINE SELECT switch on the player’s right side to “OUT.” 
2
Set “Digital Output” to “On” in “Audio Setup” (page 35).
DC IN
9.5V
LINE SELECT
AUDIO
VIDEO
PHONES
OPTICAL
OUT
A
B
IN OUT
Stereo amplifier
To AUDIO
Audio/video cord (supplied)
To AUDIO input
DC IN
9.5V
LINE SELECT
AUDIO
VIDEO
PHONES
OPTICAL
OUT
A
B
IN OUT
Amplifier with Dolby Digital 
or DTS decoder
To OPTICAL OUT
Optical digital cord (not supplied)
To AUDIO input
41
Ho
okups
Connecting to Video Player or Camcorder
To recieve the playback signal from a Video Player or Camcorder
1
Set the LINE SELECT switch on the player’s right side to “IN.” 
Note
Set the LINE SELECT switch to “OUT” after use. You cannot play back on the player if the switch is set to 
“IN.”
DC IN
9.5V
LINE SELECT
AUDIO
VIDEO
PHONES
OPTICAL
OUT
A
B
IN OUT
Video player or camcorder
To AUDIO/VIDEO
Audio/video cord (supplied)
To AUDIO/VIDEO output
42
Additional Information
Troubleshooting
If you experience any of the following 
difficulties while using the player, use this 
troubleshooting guide to help remedy the 
problem before requesting repairs. Should 
any problem persist, consult your nearest 
Sony dealer (For customers in the USA only).
Power
The power is not turned on.
, Check that the mains lead is connected 
securely.
, When using with the battery pack, check 
that the battery pack is sufficiently charged.
Picture
There is no picture/picture noise appears.
, The disc is dirty or flawed.
, The brightness is set at minimum. Set the 
brightness in “LCD Mode” (page 28).
, When you play discs, set the LINE SELECT 
switch to “OUT.” When you send the 
playback signal to other device, set the 
LINE SELECT switch to “OUT.” When 
you receive the playback signal from other 
device, set the LINE SELECT switch to 
“IN” (page 39).
, Re-connect the connecting cord securely.
, The connecting cords are damaged.
, Check the connection to your TV (page 39) 
and switch the input selector on your TV so 
that the signal from the player appears on 
the TV screen.
, The player is connected to the 
COMPONENT VIDEO IN (Y, P
B
, P
R
) jacks 
of high-vision TV.
, If the picture output from your player goes 
through your video deck to get to your TV 
or if you are connected to a combination 
TV/VIDEO player, the copy-protection 
signal applied to some DVD programmes 
could affect picture quality.
The picture does not fill the screen, even 
though the aspect ratio is set in “TV 
Display” under “General Setup.”
, The aspect ratio of the disc is fixed on your 
DVD.
The black points appear and the red, blue, 
green points remain on the LCD.
, This is a structural property of the LCD and 
not mulfunction.
Sound
There is no sound.
, The player is in pause mode or in Slow Play 
mode.
, The player is in fast forward or fast reverse 
mode.
, While playing a Super VCD on which the 
audio track 2 is not recorded, no sound will 
come out when you select “Stereo 1,” “Left 
1,” or “Right 1.”
, Re-connect the connecting cord securely.
, The connecting cord is damaged.
, The player is connected to the wrong input 
jack on the amplifier (receiver) (page 40).
, The amplifier (receiver) input is not 
correctly set.
, If the audio signal does not come through 
the OPTICAL OUT jack, check the audio 
settings (page 36).
The sound volume is low.
, The sound volume is low on some DVDs. 
The sound volume may improve if you set 
“Audio DRC” in “Audio Setup” to “On” 
(page 35).
Operation
The remote does not function.
, The batteries in the remote are weak.
, There are obstacles between the remote and 
the player.
, The distance between the remote and the 
player is too far.
, The remote is not pointed at the remote 
sensor on the player.
, Direct sunlight or strong illumination is 
striking the remote sensor.
43
Additional Information
Nothing happens when buttons are 
pressed.
, The player’s \/1/HOLD switch is set on 
“HOLD” (page 16).
The disc does not play.
, The disc is turned over.
Insert the disc with the playback side facing 
down.
, The disc is not set correctly.
, The player cannot play certain discs 
(page 7).
, The region code on the DVD does not match 
the player (page 8).
, Moisture has condensed inside the player 
(page 3).
, The player cannot play a recorded disc that 
is not correctly finalized (page 7).
, Parental Control has been set. Change the 
setting.
, The CD/DVD USB switch on the player’s 
left side is set to “USB.”
, The LINE SELECT switch on the player’s 
right side is set to “IN.”
The player starts playing the disc 
automatically.
, The disc features an auto playback function.
Playback stops automatically.
, While playing discs with an auto pause 
signal, the player stops playback at the auto 
pause signal.
Some functions such as Stop, Search, 
Scan, Slow Play, Repeat Play, or Random 
Play cannot be performed.
, Depending on the disc, you may not be able 
to do some of the operations above. Refer to 
the operating instructions supplied with the 
disc.
The language for the sound track cannot 
be changed.
, Try using the DVD’s menu instead of the 
direct selection button on the remote 
(page 17).
, Multilingual tracks are not recorded on the 
DVD being played.
, The DVD prohibits the changing of the 
language for the sound track.
The subtitle language cannot be changed 
or turned off.
, Try using the DVD’s menu instead of the 
direct selection button on the remote 
(page 17).
, Multilingual subtitles are not recorded on 
the DVD being played.
, The DVD prohibits the changing of 
subtitles.
The angles cannot be changed.
, Try using the DVD’s menu instead of the 
direct selection button on the remote 
(page 17).
, Multi-angles are not recorded on the DVD 
being played.
, The angle can only be changed when the 
” indicator lights up on the screen 
(page 19).
, The DVD prohibits changing of the angles.
The MP3 audio track cannot be played 
(page 44).
, The DATA CD is not recorded in an MP3 
format that conforms to ISO 9660 Level 1 or 
Joliet.
, The DATA DVD is not recorded in MP3 
format that conforms to UDF (Universal 
Disk Format).
, The MP3 audio track does not have the 
extension “.MP3.”
, The data is not formatted in MP3 even 
though it has the extension “.MP3.”
, The data is not MPEG-1 Audio Layer III 
data.
, The player cannot play audio tracks in 
mp3PRO format.
, The MP3 audio track is damaged.
,
continued
Page of 64
Display

Click on the first or last page to see other DVP-FX850 service manuals if exist.