Read Sony SLT-A58 / SLT-A58K / SLT-A58M / SLT-A58Y Service Manual online
SLT-A58/A58K/A58M/A58Y_L2
2-7
2-1-5. IMAGER SECTION
ns: not supplied
Screw
#64: M1.7 X 5.0 (Tapping)
(Silver)
2-666-551-21
2-666-551-21
5.0
1.7
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
Note
201
A-1935-767-A IM IMAGER UNIT ASSY (876)
(including CP6001 (CMOS imager) and IS-1007
complete board) (Note 1, 2, 3)
202
4-194-226-01
IM PLATE, LPF RETAINER
203
1-856-482-11
FILTER BLOCK, OPTICAL (Note 1, 2)
204
4-281-915-01
IM GS TAPE (Note 1)
205
4-281-914-01
IM SPACER (869) (Note 1)
206
4-194-225-01
IM TAPE FPC GUIDE
* 207
4-194-227-01
IM PLATE GUIDE IMAGER FPC
208
1-888-338-11
ISP-2001 FLEXIBLE BOARD
209
1-883-908-11
ISL-006 FLEXIBLE BOARD
#64
2-666-551-21 SCREW,
TAPPING,
P2
203
(Note 1, 2)
204
(Note 1)
205
(Note 1)
204
(Note 1)
Anti Shake Unit Section
(See page 2-8)
202
201
(including CP6001 (CMOS imager) and IS-1007 complete board)
(Note 1, 2, 3)
(Note 1, 2, 3)
208
209
206
207
#64
ns
#64
Note 1: Refer to the following statements when replacing the Optical
filter block.
Method of Removal
(1) Pour resolvent (alcohol or cleaning agent) between the
(1) Pour resolvent (alcohol or cleaning agent) between the
imager and the IM spacer.
*
Wait for that the adhesive power of the IM GS tape
weakens.
weakens.
(2) Remove the IM spacer from the imager.
Pour resolvent (alcohol or cleaning agent)
between the imager and the IM spacer.
between the imager and the IM spacer.
Method of Attachment
(1) Attach the IM GS tape and the Optical filter block by
(1) Attach the IM GS tape and the Optical filter block by
aligning them with the outer shape of the IM spacer
evenly.
*
evenly.
*
The two-layer side of the Optical filter block is on the
imager side.
(2) Attach the IM GS tape by aligning it with the
outer shape of the IM spacer evenly.
The two-layer
side is on the
imager side.
side is on the
imager side.
Mount
Side
Side
Imager
Side
Side
Optical Filter Block
Peel off the
released paper.
released paper.
Peel off the
released paper.
released paper.
Peel off the
released paper.
released paper.
IM GS Tape
IM Spacer
IM GS Tape
(3) Set the Optical filter block in its attachment jig
(J-6082-737-A), with the attached IM GS tape facing
upward.
upward.
(4) Press the imager down into the jig as shown below to
attach it to the Optical filter block.
J-6082-737-A
Imager
Peel off the released paper.
Note 2: Refer to “3-2. CLEANING PROCEDURE OF OLPF” on
page 3-2 for method of cleaning the OLPF.
Note 3: Precautions for Replacement of Imager
• If the imager has been replaced, carry out all the adjust-
ments for the camera section.
• As the imager may be damaged by static electricity from
its structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with
dusts nor exposed to strong light.
dusts nor exposed to strong light.
Ver. 1.1 2013.08
Note 1:
光学フィルタブロックを交換する際は,下記を参照してくだ
さい。
取り外し方
(1)
イメージャとIM間隔板の間に溶剤 (アルコールまたは
クリーニング液)を流し込む。
*
IM GS
テープ(イメージャ側)の粘着力が弱くなるのを
待ってください。
(2)
イメージャからIM間隔板を取り外す。
組み付け方
(1) IM
(1) IM
間隔板に対し,上下左右が均一になるようにIM GS
テープ(マウント側)および光学フィルタブロックを
貼り付ける。
*
貼り付ける。
*
光学フィルタブロックは2層側がイメージャ側に
なります。
(2) IM
間隔板に対し,上下左右が均一になるようにIM GS
テープ(イメージャ側)を貼り付ける。
イメージャ側
マウント
側
側
イメージャ
側
側
光学フィルタブロック
剥離紙を剥がす
剥離紙を剥がす
剥離紙を剥がす
(3)
貼り付けたIM GSテープ(イメージャ側)が上になるよう
に,光学フィルタブロック貼付け治具(J-6082-737-A)に
セットする。
(4)
セットする。
(4)
イメージャを図のように治具に押え付け,光学フィルタ
ブロックに貼り付ける。
イメージャ
剥離紙を剥がす
IM GS
テープ
(マウント側)
IM GS
テープ
(
テープ
(
イメージャ側)
Note 2: OLPFの清掃方法は3-2ページの 3-2. CLEANING PROCEDURE
OF OLPF を参照してください。
Note 3: イメージャ交換時の注意
・イメージャを交換した場合は,カメラ部の全調整を行っ
てください。
・イメージャは構造上,静電気により破壊される恐れがあ
るため,MOS ICと同様に注意して取り扱ってください。
また,受光部にはゴミの付着,および強い光がはいること
のないように注意してください。
のないように注意してください。
Click on the first or last page to see other SLT-A58 / SLT-A58K / SLT-A58M / SLT-A58Y service manuals if exist.