Read Sony SAL70200G2 Service Manual online
2-6
SAL70200G2 (2.8/70-200 G SSM Ⅱ) (70-200mm F2.8 G SSM II)
HELP03
Anti-diffusion agent (A-20): J-6082-611-A
Adhesive bond (B-40): J-6082-614-A
Adhesive (adhesive ivory white)
Note:
Adhesive bond (B-40): J-6082-614-A
Adhesive (adhesive ivory white)
Note:
Use the adhesive (adhesive ivory white) or the equivalent.
1. Apply the anti-diffusion agent (A-20) to the indicated portion (all circumferences) of outer barrel.
2. Install the outer barrel, aligning the CL-033 board with the switch base plate block installation window.
3. Connect the connector of switch base plate block to the CL-033 board.
4. Rotate the outer barrel in the arrow direction so that the mount index is aligned with the length hole.
5. Apply the adhesive bond (B-40) to tips of four screws and fix the switch base plate block with four screws.
6. Paint the cross-slot on the head of screw. (Four locations)
2. Install the outer barrel, aligning the CL-033 board with the switch base plate block installation window.
3. Connect the connector of switch base plate block to the CL-033 board.
4. Rotate the outer barrel in the arrow direction so that the mount index is aligned with the length hole.
5. Apply the adhesive bond (B-40) to tips of four screws and fix the switch base plate block with four screws.
6. Paint the cross-slot on the head of screw. (Four locations)
Note:
The white paint should not leak from the cross-slot.
Outer Barrel
Outer Barrel
Connector of
switch base plate block
switch base plate block
Cut view
Inside
5 mm
Outside
Cut
view
view
Apply the anti-diffusion
agent (A-20) (All round)
agent (A-20) (All round)
Switch base plate
block installation
window
block installation
window
CL-033 Board
CL-033 Board
Apply the white paint
Rotate the outer barrel
Length hole
Mount Index
Apply the
adhesive
bond (B-40)
adhesive
bond (B-40)
7. Set the zoom operation ring to the WIDE end.
8. Apply the adhesive bond (B-40) to the tips of four screws and fix the outer barrel with four screws tentatively to the extent that the outer
8. Apply the adhesive bond (B-40) to the tips of four screws and fix the outer barrel with four screws tentatively to the extent that the outer
barrel moves a little in the rotational direction.
9. Align 70 on the zoom scale with the center of index of outer barrel and tighten four screw firmly.
10. Push the outer barrel to the 1st lens and tighten the outer barrel with three slotted head paling end screws.
10. Push the outer barrel to the 1st lens and tighten the outer barrel with three slotted head paling end screws.
Then, apply the adhesive (adhesive ivory white) to head of screws (Three locations).
Note:
Note:
The adhesive (adhesive ivory white) should not seep out.
Set to the wide
end position
end position
Zoom Operation Ring
Fix with four screws tentatively
to the extent that the outer barrel
moves a little in the rotational direction.
to the extent that the outer barrel
moves a little in the rotational direction.
Apply the
adhesive
bond (B-40)
adhesive
bond (B-40)
Apply the
adhesive
bond (B-40)
adhesive
bond (B-40)
Tighten three paling end screws and
apply the adhesive (adhesive ivory white)
to the head.
apply the adhesive (adhesive ivory white)
to the head.
Align the position and
tighten the screws firmly.
tighten the screws firmly.
Index
Click on the first or last page to see other SAL70200G2 service manuals if exist.