Read Sony NEX-VG30 / NEX-VG30E / NEX-VG30EH / NEX-VG30EM / NEX-VG30H (serv.man2) Service Manual online
NEX-VG30/VG30E/VG30EH/VG30EM/VG30H_L2
2-11
Note
Screw
2-1-9. MOUNT BLOCK SECTION
ns: not supplied
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
401
A-1906-851-A MOUNT BLOCK ASSY (SERVICE)
(including ASM080 (CMOS imager) and IS-073 board)
(Note 5)
402
4-185-968-02
MB TAPE, MASK SHEET (Note 3)
403
4-185-966-01
MB SHEET, MASK (Note 3)
404
1-487-960-23
SHUTTER UNIT (AFE-3032)
* 405
4-260-738-01 TAPE AS (075)
406
4-408-518-01
SHEET (IS), ELECTROSTATIC
407
4-257-741-01
GUARD SHEET, HINGE FPC
* 408
Selection Parts IM WASHER (A), ADJUST (Note 1, 2)
* 409
Selection Parts IM WASHER (B), ADJUST (Note 1, 2)
* 410
Selection Parts IM WASHER (C), ADJUST (Note 1, 2)
411
A-1773-803-A MB CHARGE UNIT
412
4-299-977-01
HEAT SINK (MT)
413
4-299-978-01
SHEET (MT (UPPER)), RADIATION (Note 4)
414
1-884-094-11
FP-1433 FLEXIBLE BOARD
415
1-884-095-11
FP-1434 FLEXIBLE BOARD
416
1-884-110-11
FP-1449 FLEXIBLE BOARD
417
4-299-979-01
SHEET (MT (LOWER)), RADIATION (Note 4)
418
4-299-976-01 FRAME,
MT
419
A-1912-812-A MT-1003 BOARD, COMPLETE (SERVICE)
420
4-408-576-01
TAPE (AS (0932))
421
1-884-109-11
FP-1448 FLEXIBLE BOARD
422
4-188-536-01 CAP,
BODY
423
4-408-483-01
SHEET (IS (361)), RADIATION
424
4-300-016-01
HEAT SINK (IM)
#2
2-635-562-31 SCREW
(M1.7)
#27
2-662-396-11
SCREW (M14), NEW TRU-STAR, P2
#46
2-660-401-11
SCREW (M1.7), NEW TRU-STAR, P2
#191 4-188-735-01 SCREW
(M1.7)
#197
4-185-990-01
MB SCREW, CHARGE UNIT FIXED
#198
4-186-545-01
SCREW, 0+Z M1.7 SG (SPIN) (Note 6)
#2: M1.7 X 4.0
(Black)
2-635-562-31
2-635-562-31
4.0
1.7
#46: M1.7 X 3.0
(Red)
2-660-401-11
2-660-401-11
3.0
1.7
#191: M1.7 X 3.5 (Tapping)
(Black)
4-188-735-01
4-188-735-01
3.5
1.7
4.5
1.6
M1.6 X 4.5 (Tapping)
#197:
(Silver)
4-185-990-01
4-185-990-01
Note 1: The IM adjust washers (A, B, C) differ in thickness.
Make sure to return the removed IM adjust washers to
original places.
original places.
When replacing IM adjust washers, refer to “2-2. SELECTION
PARTS” on page 2-16.
PARTS” on page 2-16.
If the original state cannot be restored due to loss of
the IM adjust washer, for example, replace the Mount
Block Assy (Service).
the IM adjust washer, for example, replace the Mount
Block Assy (Service).
Note 2: Refer to “Assembly-5: Putting position of the IM Adjust
Washer (A, B, C) ” when you assemble.
Note 3: Refer to “Assembly-6: Method of attachment of the MB Mask
Sheet” when you assemble.
Note 4: Do not reuse the Radiation Sheet (MT (Upper)) and the
Radiation Sheet (MT (Lower)) because their adhesive force
decreases when they are removed once.
decreases when they are removed once.
Note 1: IM調整ワッシャ (A, B, C)は,それぞれ厚さが異なります。
取り外したIM調整ワッシャは,必ず元の位置に戻してくだ
さい。
さい。
また,IM調整ワッシャを交換する際は,2-16ページの “2-2.
SELECTION PARTS”を参照してください。
IM adjust washerを紛失するなどして元の状態に戻せなく
なった場合は,Mount Block Assy (Service) を交換してくだ
さい。
なった場合は,Mount Block Assy (Service) を交換してくだ
さい。
Note 2: 組立時は“Assembly-5: Putting position of the IM Adjust
Washer (A, B, C) ”を参照してください。
Note 3: 組立時は“Assembly-6: Method of attachment of the MB Mask
Sheet”を参照してください。
Note 4: Radiation Sheet (MT (Upper))とRadiation Sheet (MT (Lower))
は一度剥がすと粘着力が弱くなるため,再利用はしないで
ください。
ください。
Note 5: Precautions for Replacement of the Mount Block Assy Service
As Mount Block Assy Service may be damaged by static elec-
tricity from its structure, handle it carefully like for the MOS IC.
tricity from its structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with dusts
nor exposed to strong light.
nor exposed to strong light.
Note 5: マウントブロックAssy サービス交換時の注意
マウントブロックAssy サービスは構造上,静電気により破
壊される恐れがあるため,MOS ICと同様に注意して取り
扱ってください。
壊される恐れがあるため,MOS ICと同様に注意して取り
扱ってください。
また,受光部にはゴミの付着,および強い光がはいること
のないように注意してください。
のないように注意してください。
#191
#191
#46
#191
ns ns
#197
#198
(Note 6)
#2
#2
#191
#27
B
A
A
B
421
407
419
416
415
414
406
423
424
418
417
(Note 4)
413
(Note 4)
412
410
(Note 1, 2)
411
409
(Note 1, 2)
408
(Note 1, 2)
402
(Note 3)
404
405
422
(including ASM080 (CMOS imager)
and IS-073 board)
(Note 5)
and IS-073 board)
(Note 5)
Cabinet (F) Section
(See Page 2-12)
401
403
(Note 3)
Imager Unit Section
(See Page 2-13)
420
Be careful not to drop.
Be careful not to drop.
4.0
1.7
#198: M1.7 X 4.0
(Silver)
4-186-545-01
4-186-545-01
Note 6: This screw cannot be reused. Discard the screw removed
once in servicing.
Instead, use a new screw.
Note 6: このねじは再利用することができません。
サービス対応時に一度でも外した場合は新品のねじと交換
してください。
してください。
#27: M1.4 X 2.0
(Black)
2-662-396-11
2-662-396-11
2.0
1.4
Click on the first or last page to see other NEX-VG30 / NEX-VG30E / NEX-VG30EH / NEX-VG30EM / NEX-VG30H (serv.man2) service manuals if exist.