Read Sony NEX-FS700 / NEX-FS700C / NEX-FS700CK / NEX-FS700E / NEX-FS700EK / NEX-FS700J / NEX-FS700JK / NEX-FS700K / NEX-FS700R / NEX-FS700RH / NEX-FS700U / NEX-FS700UK Service Manual online
2-11
NEX-FS700/FS700K/FS700C/FS700CK/FS700E/FS700EK/FS700J/FS700JK/FS700R/FS700RH/FS700U/FS700UK
2-1-9. LCD SECTION
Note
Screw
Note 3: Refer to “Assembly-7: Apply grease on the LCD Lock
Bolt.”.
Note 3: “Assembly-7: Apply grease on the LCD Lock Bolt.”を
参照してください。
Note 4: Cut SHEET, LIGHT INTERCEPTION (3-089-986-01)
into the desired length and use it.
Note 4: SHEET, LIGHT INTERCEPTION (3-089-986-01) は
指定のサイズに切って使用すること。
401
4-269-207-01
CABINET (C), P (Note 1)
402
A-1885-281-A PD-468 BOARD, COMPLETE
403
4-269-204-01 SHEET
(PD)
404
4-269-203-01 FRAME,
LCD
405
4-283-280-11
CUSHION (91000), LCD
406
4-269-202-11
CABINET (M), P
407
1-471-504-11
MAGNET (ND5X3.5X2.4-B) (Note 2)
408
4-269-197-01
CAP, LCD KNOB
409
4-269-196-01
KNOB, LCD LOCK
410
4-269-195-01
BOLT, LCD LOCK (Note 3)
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
411
4-269-206-01
CABINET (REAR), HINGE
412
1-967-783-11
HARNESS (COAXIAL CABLE)
413
X-2580-324-1 HINGE
ASSY,
PANEL
414
4-269-205-01
CABINET (FRONT), HINGE
415
3-089-986-01
SHEET (L), LIGHT INTERCEPTION (Note 4)
416
A-1885-373-A PANEL BLOCK ASSY, LCD
LCD901 1-811-403-11
LCD WITH TOUCH PANEL
LED901 1-487-270-11
BLOCK, LIGHT GUIDE PLATE (3.5)
#49
2-630-005-31
SCREW (M2), NEW TRUSTER, P2
#50
2-891-494-11
SCREW (M2), NEW TRUSTER, P2
#49: M2.0 X 4.0
(Black)
2-630-005-31
2-630-005-31
4.0
2.0
#50: M2.0 X 3.0
(Red)
2-891-494-11
2-891-494-11
3.0
2.0
1. The meaning of the symbol in left figure is as follows. Be careful when you remove it.
◇ : Solder
DISASSEMBLY
PD-468
#50
#49
#49
#49
#50
#50
#49
LCD901
LED901
401
(Note 1)
403
404
405
406
407
(Note 2)
409
408
410
(Note 3)
414
416
413
411
412
402
415
(Size: 5.0mm X 5.0mm)
(Note 4)
(Note 4)
マグネットを取付ける際は,
マ−キング面を図の位置に
あわせてください。
マ−キング面を図の位置に
あわせてください。
マーキング
Note 1:
1
2
Claws
Install the P cabinet (C) assembly in the
following procedure to prevent the claw of P
cabinet (C) assembly from breaking.
following procedure to prevent the claw of P
cabinet (C) assembly from breaking.
Lift up the opposite side of the claw of P cabinet
(C) assembly in the arrow direction.
(C) assembly in the arrow direction.
Remove the P cabinet (C) assembly, sliding it in
the arrow direction.
the arrow direction.
Note 1:
P Cabinet (C) Assyの爪の無い側を矢印方向に
持ち上げる。
持ち上げる。
P Cabinet (C) Assyの爪を折らないために、
以下の手順でP Cabinet (C) Assyを取り外し
てください。
以下の手順でP Cabinet (C) Assyを取り外し
てください。
1
P Cabinet (C) Assyを矢印方向にスライドさせて
P Cabinet (C) Assyを取り外す。
P Cabinet (C) Assyを取り外す。
2
Claws
Install the magnet with the
marking oriented as shown
below.
marking oriented as shown
below.
Marking
Note 2:
Note 2:
Click on the first or last page to see other NEX-FS700 / NEX-FS700C / NEX-FS700CK / NEX-FS700E / NEX-FS700EK / NEX-FS700J / NEX-FS700JK / NEX-FS700K / NEX-FS700R / NEX-FS700RH / NEX-FS700U / NEX-FS700UK service manuals if exist.