Read Sony NEX-7 / NEX-7K (serv.man2) Service Manual online
NEX-7/7K_L2
2-9
2-1-7. IMAGER BLOCK SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
301
4-281-196-01
SHEET, MASK SHEET ADHESIVE (Note 4)
302
4-277-282-11
MB SHEET (754), MASK (Note 4)
303
1-487-619-21
SHUTTER UNIT (H094)
304
A-1817-096-B MB CHARGE UNIT (755)
305
4-288-878-01
SHEET, CUSHION (SH)
* 306
Selection Parts IM WASHER (A), ADJUST (Note 2, 3)
* 307
Selection Parts IM WASHER (B), ADJUST (Note 2, 3)
* 308
Selection Parts IM WASHER (C), ADJUST (Note 2, 3)
309
4-292-165-01
SHEET, IMAGER ELECTRIC HEAT
310
4-300-303-01
PLATE (IM) (600), RADIATION
311
A-1857-129-A (FRONT) BLOCK ASSY (SERVICE)
(including CP6001 (CMOS imager) and IS-095 complete
board) (Note 5)
board) (Note 5)
#177
3-208-537-21
0+Z M1.4X2 NEW TORASUTA
#197
4-185-990-01
MB SCREW, CHARGE UNIT FIXED
#238
4-287-436-01
SCREW (M1.7) (Note 1)
#197
#177
#238
(Note 1)
(Note 1)
2
Imager Unit Section
(See page 2-10)
3
303
4
304
301
(Note 4)
302
(Note 4)
1
310
306
(Note 2, 3)
307
(Note 2, 3)
309
308
(Note 2, 3)
305
Cabinet (Front) Section
(See page 2-11)
311
(including CP6001 (CMOS imager)
and IS-095 complete board)
(Note 5)
and IS-095 complete board)
(Note 5)
DISASSEMBLY
1. Remove in numerical order (
1
to
4
) in the left figure.
Screw
#177: M1.4 X 2.5
(Red)
3-208-537-21
3-208-537-21
2.5
1.4
#197: M1.6 X 4.5 (Tapping)
(Silver)
4-185-990-01
4-185-990-01
4.5
1.6
3
#177 X 3
1
#238 X 3
Back View
#238
#177
Back View
#238:
M1.7 X 3.5
(Black)
4-287-436-01
(Black)
4-287-436-01
3.5
1.7
Note 1: Refer to “Assembly-1: Screw tightening sequence when
assembling the Heat Sink (IM).”.
Note 1: Assembly-1: Screw tightening sequence when assembling
the Heat Sink (IM). を参照してください。
Note
Note 2: The IM adjust washers (A, B, C) differ in thickness.
Make sure to return the removed IM adjust washers to origi-
nal places.
nal places.
When replacing IM adjust washers, refer to “2-2. SELEC-
TION PARTS” on page 2-12.
TION PARTS” on page 2-12.
If the original state cannot be restored due to loss of the IM
adjust washer, for example, replace the Mount Block Assy
(Service).
adjust washer, for example, replace the Mount Block Assy
(Service).
Note 2: IM調整ワッシャ (A, B, C)は,それぞれ厚さが異なります。
取り外したIM調整ワッシャは,必ず元の位置に戻してくださ
い。
い。
また,IM調整ワッシャを交換する際は,2-12ページの 2-2.
SELECTION PARTS を参照してください。
IM adjust washerを紛失するなどして元の状態に戻せなく
なった場合は,Mount Block Assy (Service) を交換してくだ
さい。
なった場合は,Mount Block Assy (Service) を交換してくだ
さい。
Note 3: Refer to “Assembly-2: IM Adjust Washer (A, B, C) putting
position” when you assemble.
Note 3: 組立時は Assembly-2: IM Adjust Washer (A, B, C) putting
position を参照してください。
Note 4: Refer to “Assembly-4: Method of attachment of the MB
Mask Sheet (754)” when you assemble.
Note 4: 組立時は Assembly-4: Method of attachment of the MB
Mask Sheet (754) を参照してください。
Note 5: Precautions for Replacement of the Mount Block Assy
Service
As Mount Block Assy Service may be damaged by static
electricity from its structure, handle it carefully like for the
MOS IC.
electricity from its structure, handle it carefully like for the
MOS IC.
In addition, ensure that the receiver is not covered with
dusts nor exposed to strong light.
dusts nor exposed to strong light.
Note 5: マウントブロックAssy サービス交換時の注意
マウントブロックAssy サービスは構造上,静電気により破壊
される恐れがあるため,MOS ICと同様に注意して取り扱って
される恐れがあるため,MOS ICと同様に注意して取り扱って
ください。
また,受光部にはゴミの付着,および強い光がはいることの
ないように注意してください。
ないように注意してください。
The changed portions from
Ver. 1.3 are shown in blue.
Ver. 1.3 are shown in blue.
Ver. 1.4 2012.07
Click on the first or last page to see other NEX-7 / NEX-7K (serv.man2) service manuals if exist.