Read Sony ILCA-77M2 / ILCA-77M2M / ILCA-77M2Q Service Manual online
ILCA-77M2/77M2M/77M2Q_L2
2-13
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
451
4-194-226-01
IM PLATE, LPF RETAINER
452
A-2042-734-A IM IMAGER UNIT ASSY (880) (Note 1, 2)
453
4-534-930-01
IM MASK PLATE (880)
454
4-281-915-01
IM GS TAPE (Note 1)
455
4-185-993-02
IM SHEET, SPACER (Note 1)
456
1-884-796-21
ISP-004 FLEXIBLE BOARD
457
1-884-795-21
ISL-005 FLEXIBLE BOARD
458
4-421-277-01
IM SHEET, RADIATION (874)
459
4-421-276-01
IM HEAT SINK (874)
460
4-194-225-01
IM TAPE FPC GUIDE
* 461
4-194-227-01
IM PLATE GUIDE IMAGER FPC
462
4-295-215-01
IM SHEET GRAPHITE 870
463
A-2059-919-A OPTICAL FILTER BLOCK (SERVICE) (Note 1, 2, 3)
#64
2-666-551-21 SCREW,
TAPPING,
P2
Note
Screw
2-1-10. IMAGER SECTION
ns: not supplied
#64: M1.7 X 5.0 (Tapping)
(Silver)
2-666-551-21
2-666-551-21
5.0
1.7
ns
#64
#64
Anti Shake Unit Section
(See page 2-14)
(including HOL-007 flexible board)
458
460
459
461
457
456
455
(Note 1)
454
(Note 1)
463
(Note 1, 2, 3)
454
(Note 1)
451
453
462
452
(including CP6001 (CMOS imager) and
IS-095 complete board)
(Note 1, 2)
IS-095 complete board)
(Note 1, 2)
Note 1: Refer to “3-2. CLEANING PROCEDURE OF OLPF” on
page 3-2 for method of cleaning the OLPF.
Note 1: OLPFの清掃方法は3-2ページの “3-2. CLEANING PROCE-
DURE OF OLPF” を参照してください。
Note 2:
Precautions for Replacement of Imager
•
•
If the imager has been replaced, carry out all the adjustments for the
camera section.
camera section.
•
As the imager may be damaged by static electricity from its structure,
handle it carefully like for the MOS IC.
handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with dusts nor
exposed to strong light.
exposed to strong light.
Note 2:
イメージャ交換時の注意
イメージャ交換時の注意
・ イメージャを交換した場合は,カメラ部の全調整を行ってくださ
い。
・ イメージャは構造上,静電気により破壊される恐れがあるため,
MOS ICと同様に注意して取り扱ってください。
また,受光部にはゴミの付着,および強い光がはいることのない
ように注意してください。
Note 3 :
J-6082-737-A
Refer to the following statements when replacing the Optical
filter block.
filter block.
Method of Removal
(1) Pour resolvent (alcohol or cleaning agent) between the
(1) Pour resolvent (alcohol or cleaning agent) between the
imager and the IM spacer.
*
*
Wait for that the adhesive power of the IM spacer
weakens.
weakens.
(2) Remove the IM spacer from the imager.
Method of Attachment
*
Confirm the mounting direction of the Optical filter
block referring to "3-1. ASSEMBLY".
(2) Set the Optical filter block in its attachment jig
(J-6082-737-A), with the attached adhesive side of IM
(J-6082-737-A), with the attached adhesive side of IM
spacer facing upward.
(3) Press the imager down into the jig as shown below to
attach it to the Optical filter block.
Imager
Peel off the release paper.
Pour resolvent (alcohol or
cleaning agent) between
the imager and the IM spacer.
cleaning agent) between
the imager and the IM spacer.
Optical Filter Block
Peel off the
release paper
release paper
Peel off the
release paper
release paper
Peel off the
release paper
release paper
IM GS Tape
IM GS Tape
IM Spacer
Peel off the
release paper
release paper
(1) Attach the two IM GS tapes and the Optical filter block
by aligning them with the outer shape of the IM
spacer evenly.
by aligning them with the outer shape of the IM
spacer evenly.
Note 3 :
J-6082-737-A
光学フィルタブロックを交換する際は,下記を参照してくだ
さい。
さい。
取り外し方
(1) イメージャとIM間隔板の間に溶剤(アルコールまたはク
リーニング液)を流し込む。
* IM間隔板の粘着力が弱くなるのを待ってください。
(2) イメージャからIM間隔板を取り外す。
(1) イメージャとIM間隔板の間に溶剤(アルコールまたはク
リーニング液)を流し込む。
* IM間隔板の粘着力が弱くなるのを待ってください。
(2) イメージャからIM間隔板を取り外す。
イメージャとIM間隔板の間に溶剤
(アルコールまたはクリーニング液)
を流し込む。
(アルコールまたはクリーニング液)
を流し込む。
組み付け方
(1) IM間隔板に対し,上下左右が均一になるように
IM GS TAPE2枚および光学フィルタブロックを貼り
付ける。
* "3-1. ASSEMBLY"を参照し,光学フィルタブロックの
取り付ける向きを確認してください。
(1) IM間隔板に対し,上下左右が均一になるように
IM GS TAPE2枚および光学フィルタブロックを貼り
付ける。
* "3-1. ASSEMBLY"を参照し,光学フィルタブロックの
取り付ける向きを確認してください。
剥離紙を剥がす
剥離紙を剥がす
剥離紙を剥がす
IM間隔板
IM GS TAPE
剥離紙を剥がす
IM GS TAPE
(2) IM GS TAPEの粘着面が上になるように,光学フィルタブロッ
ク貼付け治具(J-6082-737-A)にセットする。
(3) イメージャを図のように治具に押え付け,光学フィルタブ
ロックに貼り付ける。
ク貼付け治具(J-6082-737-A)にセットする。
(3) イメージャを図のように治具に押え付け,光学フィルタブ
ロックに貼り付ける。
イメージャ
剥離紙を剥がす
光学フィルタブロック
Click on the first or last page to see other ILCA-77M2 / ILCA-77M2M / ILCA-77M2Q service manuals if exist.