DSLR-A700P - Sony Digital Camera Service Manual (repair manual)

dslr-a700p service manual
Model
DSLR-A700P
Pages
127
Size
5.83 MB
Type
PDF
Document
Service Manual
Brand
Device
Digital Camera
File
dslr-a700p.pdf
Date

Read Sony DSLR-A700P Service Manual online

SERVICE NOTE
SPECIFICATIONS
REPAIR PARTS LIST
DISASSEMBLY
ADJUSTMENTS
SERVICE MANUAL
Revision History
Revision History
Sony EMCS Co.
SAL16105 (DT 3.5-5.6/16-105) (DT 16-105mm F3.5-5.6)
SERVICE NOTE
SPECIFICATIONS
REPAIR PARTS LIST
DISASSEMBLY
ADJUSTMENTS
Link (Japanese)
Link (Japanese)
・レンズ投影器と完成検査治具について
分解図につきましては,英語版を
ご参照ください。
Link (English)
Link (English)
Ver. 1.5  2009.12
LENS FOR DSLR CAMERA
2009L0800-1
  © 2009.12
Published by Tokai TEC
9-852-220-16
US Model
Canadian Model
AEP Model
Chinese Model
Japanese Model
SAL16105
(DT 3.5-5.6/16-105) (DT 16-105mm F3.5-5.6)
• About the Lens Test Projector and Finished Inspection JIG
Revised-4
Replace the previously issued
SERVICE MANUAL 9-852-220-15
with this Manual.
— 2 —
SAL16105 (DT 3.5-5.6/16-105) (DT 16-105mm F3.5-5.6)
SPECIFICATIONS
• This lens is equipped with a distance encoder. The distance encoder allows more accurate measurement (ADI) by using a flash for ADI.
• Depending on the lens mechanism, the focal length may change with any change of the shooting distance. The focal length assumes the lens is focused
at infinity.
Equivalent 35mm-format focal length
 
*
1
 (mm)
24-157.5
Lens groups elements
11-15
Angle of view
 
*
1
83
°-15°
*
1
The values for equivalent 35mm-format focal length and angle of view are based on Digital Single Lens Reflex Cameras equipped with an APS-
C sized image sensor.
Minimum focus
 
*
2
 (m (feet))
0.4 (1.3)
*
2
Minimum focus is the shortest distance from the image sensor to the subject.
Maximum magnification (X)
0.23
Minimum f-stop
f/22-36
Filter diameter (mm)
62
Dimensions (maximum diameter 
×××××
 height) (mm (in.))
Approx. 72 
× 83 (2 7/8 × 3 3/8)
Mass (g (oz.))
Approx. 470 (16 9/16)
Included items
Lens (1), Front lens cap (1), Rear lens cap (1), Lens hood (1), Set of printed documentation
Designs and specifications are subject to change without notice.
WIDE
TELE
1st Lens
(52.148mm)
2nd Lens
(11.957mm)
3rd Lens
(26.798mm)
4th Lens
(36.716mm)
Extra-Low Dispersion Glass
Aspheric Lens
1-1
SAL16105 (DT 3.5-5.6/16-105) (DT 16-105mm F3.5-5.6)
1. SERVICE NOTE
1-1.
Chemicals
Some chemicals used for servicing are highly volatile.
Their evaporation caused by improper management affects your health and environment, and wastes resources.
Manage the chemicals carefully as follows.
• Store chemicals sealed in a specific place to prevent from exposure to high temperature or direct sunlight.
• Avoid dividing chemicals into excessive numbers of small containers to reduce natural evaporation.
• Keep containers sealed to avoid natural evaporation when chemicals are not in use.
• Avoid using chemicals as much as possible. When using chemicals, divide only required amount to a small plate from the container and
use up it.
1-2.
Exterior Parts
Be careful to the following points for exterior parts used in this unit.
• Use a piece of cleaning paper or cleaning cloth for cleaning exterior parts. Avoid using chemicals.
Even if you have to use chemicals to clean heavy dirt, don’t use paint thinner, ketone, nor alcohol.
• Insert the specific screws vertically to the part when installing a exterior part.
Be careful not to tighten screws too much.
1-3.
Unleaded Solder
This unit uses unleaded solder.
Boards requiring use of unleaded solder are printed with the lead free mark (LF) indicating the solder contains no lead.
(
Caution:
Some printed circuit boards may not come printed with the lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
• Set the soldering iron tip temperature to 350 
°C approximately.
If cannot control temperature, solder/unsolder at high temperature for a short time.
Caution:
The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful!
Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Be sure to control soldering iron tips used for unleaded solder and those for leaded solder so they are managed separately. Mixing
unleaded solder and leaded solder will cause detachment phenomenon.
1-2
SAL16105 (DT 3.5-5.6/16-105) (DT 16-105mm F3.5-5.6)
1-4.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer.
1.
Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and
bridges.
2.
Check the interboard wiring to ensure that no wires are “pinched” or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their
replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 
°C during repairing.
• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering or unsoldering.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 
0
 OR DOTTED LINE WITH
MARK 
0
 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 
0
 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Page of 127
Display

Download Sony DSLR-A700P Service Manual (Repair Manual)

Here you can read online and download Sony DSLR-A700P Service Manual in PDF. DSLR-A700P service manual will guide through the process and help you recover, restore, fix, disassemble and repair Sony DSLR-A700P Digital Camera. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.