Read Sony DSLR-A100 / DSLR-A100H / DSLR-A100K / DSLR-A100W (serv.man2) Service Manual online
SERVICE MANUAL
LEVEL
1
Link
SERVICE NOTE
SPECIFICATIONS
ACCESSORIES
INSTRUCTION MANUAL
Link
Revision History
Revision History
Sony EMCS Co.
DSLR-A100_L1
Ver. 1.3 2007.10
DIGITAL SINGLE LENS REFLEX CAMERA
2007J0500-1
© 2007.10
Published by Kohda TEC
9-852-130-42
The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number
specified.
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
DSLR-A100
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
Hong Kong Model
Chinese Model
Korea Model
Japanese Model
Tourist Model
Revised-1
Replace the previously issued
SERVICE MANUAL 9-852-130-41
with this manual.
SERVICE MANUAL 9-852-130-41
with this manual.
— 2 —
DSLR-A100_L1
SPECIFICATIONS
Camera
[System]
Camera Type
Digital Single Lens Reflex
Camera with built-in flash and
interchangeable lenses
Camera with built-in flash and
interchangeable lenses
Lens
All of Sony Lens
[CCD]
Total pixel number of camera
Approx. 10 800 000 pixels
Effective pixel number of camera
Approx. 10 200 000 pixels
Image sensor
23.6
× 15.8mm (APS-C format)
Interlace scan Primary Color
[Super SteadyShot]
System
CCD-Shift mechanism
Super SteadyShot Compensation capability
Approximately 2 EV to 3.5 EV
decrease in shutter speed
(varies according to shooting
conditions and lens used)
decrease in shutter speed
(varies according to shooting
conditions and lens used)
[Anti-Dust]
System
Charge protection coating on
Low-Pass Filter and CCD-Shift
mechanism
Low-Pass Filter and CCD-Shift
mechanism
[Viewfinder]
Type
Fixed eye-level system with
roof mirror type pentaprism
roof mirror type pentaprism
Focusing Screen Spherical Acute Matte
Field of View
0.95
Magnification
0.83
× with 50 mm lens at
infinity, –1 m
–1
Eye Relief
Approximately 20mm from the
eyepiece, 16mm from the
eyepiece frame at –1 diopter
(–1m
eyepiece, 16mm from the
eyepiece frame at –1 diopter
(–1m
–1
)
Dioptor Adjustment
–2.5 to +1.0 m
–1
[Auto Focus System]
System
TTL phase-detection system,
CCD line sensors (9 points, 8
lines with center cross-hair
sensor)
CCD line sensors (9 points, 8
lines with center cross-hair
sensor)
Sensitivity Range
0 EV to 18 EV (at ISO 100
equivalent)
equivalent)
[Exposure]
Metering Cell
40-segment honeycomb-pattern
SPC
SPC
Metering Range +1 EV to +20 EV (+4 EV to
+20 EV with Spot metering),
(at ISO 100 with F1.4 lens)
(at ISO 100 with F1.4 lens)
[Shutter]
Type
Electronically-controlled,
vertical-traverse, focal-plane
type
vertical-traverse, focal-plane
type
Speed range
1/4000 second to 30 seconds,
bulb
bulb
Flash Sync Speed
1/160 second (with Super
SteadyShot off),
1/125 second (with Super
SteadyShot on)
SteadyShot off),
1/125 second (with Super
SteadyShot on)
[Built-In-Flash]
Flash G.No.
GN 12 (in meters at ISO 100)
Recycling Time
Approx. 3 seconds
[Recording media]
CompactFlash card(TypeI,II),
Microdrive, “Memory Stick
Duo” (with Memory Stick Duo
Adaptor for CF Slot)
Microdrive, “Memory Stick
Duo” (with Memory Stick Duo
Adaptor for CF Slot)
[LCD monitor]
LCD panel
6.2 cm (2.5type) TFT drive
Total number of dots
230 000 (960
×240) dots
[Power, general]
Used battery pack
Rechargeable battery pack
NP-FM55H
NP-FM55H
[Others]
PictBridge
Compatible
Exif Print
Compatible
PRINT Image Matching III
Compatible
Dimensions
133.1
× 94.7 × 71.3 mm
(5 1/4
× 3 3/4 × 2 7/8 inches)
(W/H/D, excluding protrusions)
Mass
Approx.545 g (1 lb 3.2 oz)
(without batteries, recording
medium and body accessories)
(without batteries, recording
medium and body accessories)
Operating temperature
0 to +40
°C (+32 to +104°F)
(When using the Microdrive:
+5 to +40
+5 to +40
°C (41 to +104°F))
Exif
Exif Ver. 2.21
USB communication
Hi-Speed USB (USB 2.0
compliant)
compliant)
BC-VM10 Battery charger
Input rating
100 V to 240 V AC, 50/60 Hz
Output rating
8.4 V DC, 750 mA
Operating temperature range
0 to +40
°C (32 to +104°F)
Storage temperature range
-20 to +60
°C (-4 to +140°F)
Maximum dimensions
Approx. 70
× 25 × 95 mm
(2 7/8
× 1× 3 3/4 inches) (W/H/
D)
Mass
Approx. 90 g (3.2 oz)
Rechargeable battery pack NP-FM55H
Used battery
Lithium-ion battery
Maximum voltage
DC 8.4 V
Nominal voltage DC 7.2 V
Capacity
11.5 Wh (1 600 mAh)
Maximum dimensions
Approx. 38.2
× 20.5 × 55.6 mm
(1 9/16
× 13/16 × 2 1/4 inches)
(W/H/D)
Mass
Approx. 78 g (2.8 oz)
Design and specifications are subject to change
without notice.
without notice.
— 3 —
DSLR-A100_L1
SERVICE NOTE
1. CHEMICALS
Some chemicals used for servicing are highly volatile.
Their evaporation caused by improper management affects your health and environment, and wastes resources.
Manage the chemicals carefully as follows.
Their evaporation caused by improper management affects your health and environment, and wastes resources.
Manage the chemicals carefully as follows.
•
Store chemicals sealed in a specific place to prevent from exposure to high temperature or direct sunlight.
•
Avoid dividing chemicals into excessive numbers of small containers to reduce natural evaporation.
•
Keep containers sealed to avoid natural evaporation when chemicals are not in use.
•
Avoid using chemicals as much as possible. When using chemicals, divide only required amount to a small plate from the container and
use up it.
use up it.
2. EXTERIOR PARTS
Be careful to the following points for plastic parts used in this unit.
•
Use a piece of cleaning paper or cleaning cloth for cleaning plastic parts. Avoid using chemicals.
Even if you have to use chemicals to clean heavy dirt, don’t use paint thinner, ketone, nor alcohol.
Even if you have to use chemicals to clean heavy dirt, don’t use paint thinner, ketone, nor alcohol.
•
Insert the specific screws vertically to the part when installing a plastic part.
Be careful not to tighten screws too much.
Be careful not to tighten screws too much.
3. UNLEADED SOLDER
This unit uses unleaded solder.
Boards requiring use of unleaded solder are printed with the lead free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)
Boards requiring use of unleaded solder are printed with the lead free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
•
Set the soldering iron tip temperature to 350
°C approximately.
If cannot control temperature, solder/unsolder at high temperature for a short time.
Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful!
Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful!
Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur
such as on IC pins, etc.
such as on IC pins, etc.
•
Be sure to control soldering iron tips used for unleaded solder and those for leaded solder so they are managed separately. Mixing
unleaded solder and leaded solder will cause detachment phenomenon.
unleaded solder and leaded solder will cause detachment phenomenon.
4. SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer.
1.
Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and
bridges.
bridges.
2.
Check the interboard wiring to ensure that no wires are “pinched” or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their
replacement.
replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
Flexible Circuit Board Repairing
•
•
Keep the temperature of the soldering iron around 270
°C during repairing.
•
Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).
•
Be careful not to apply force on the conductor when soldering or unsoldering.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Replace only with the same or equivalent type.
— 4 —
DSLR-A100_L1
ACCESSORIES
• Refer to the cover for mark
0
.
Checking supplied accessories.
Note:
• Items marked “*” are not stocked since they are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• The parts numbers of such as a cabinet are also appeared in this section.
Refer to the parts number mentioned below the name of parts to order.
• Abbreviation
AR : Argentine model
AUS: Australian model
BR : Brazilian model
AUS: Australian model
BR : Brazilian model
CH : Chinese model
CND: Canadian model
EE : East European model
CND: Canadian model
EE : East European model
HK : Hong Kong model
J
J
: Japanese model
JE
: Tourist model
KR : Korea model
NE : North European model
TW : Taiwan model
NE : North European model
TW : Taiwan model
Battery Charger
(BC-VM10)
(BC-VM10)
0
1-479-742-21
(US, CND)
(US, CND)
0
1-479-742-31
(Except US, CND)
(Except US, CND)
Power Cord
0
1-555-074-
91
(AUS)
0
1-782-476-41 (CH)
0
1-790-107-
61
(US, CND)
0
1-792-549-
41
(JE, J)
0
1-833-892-21
(KR)
0
1-824-910-
71
(AEP, E)
0
1-827-269-
12
(UK,
HK
)
0
1-830-518-
41
(TW)
Rechargeable Battery Pack
(NP-FM55H)
(NP-FM55H)
(
Note
)
Memory Stick Duo Adaptor for
Compact Flash Slot (AD-MSCF1)
Compact Flash Slot (AD-MSCF1)
1-797-601-11
USB Cable
1-833-062-
12
Video Cable
1-833-063-11
Shoulder Strap with
Eye Piece Cover and
Remote Commander Clip
Eye Piece Cover and
Remote Commander Clip
2-688-782-
02
Body Cap
(ALC-B55)
(Attached on the camera)
(ALC-B55)
(Attached on the camera)
2-688-728-
02
Accessory Shoe Cap
(Attached on the camera)
(Attached on the camera)
2-688-767-
02
(BLACK)
2-688-767-11 (SILVER)
CD-ROM
(
(
α
100 Application Software)
2-683-121-
02
Conversion (2P) Adaptor
0
1-569-007-12 (JE)
Conversion (2P) Adaptor
0
1-569-008-12 (E)
Body Cap Seal
(with
(with
α
(alpha) logo)
2-894-387-01
Other accessories
2-681-186-01 INSTRUCTION (Read This First) (JAPANESE) (J)
2-681-186-11 INSTRUCTION (Read This First) (ENGLISH)
2-681-186-11 INSTRUCTION (Read This First) (ENGLISH)
(EXCEPT CH, KR, J)
2-681-186-21 INSTRUCTION (Read This First) (FRENCH, ITALIAN)
(CND, AEP)
2-681-186-31 INSTRUCTION (Read This First)
(SPANISH, PORTUGUESE) (AEP, E, JE)
2-681-186-41 INSTRUCTION (Read This First) (GERMAN, DUTCH)
(AEP)
2-681-186-51 INSTRUCTION (Read This First)
(TRADITIONAL CHINESE, SIMPLIFIED CHINESE)
(E, HK, CH, TW, JE)
2-681-186-61 INSTRUCTION (Read This First) (RUSSIAN) (AEP)
2-681-186-71 INSTRUCTION (Read This First) (ARABIC, PERSIAN) (E)
2-681-186-81 INSTRUCTION (Read This First) (KOREAN) (KR, JE)
2-689-105-11 INSTRUCTION (Read This First) (HUNGARIAN, SLOVAK,
2-681-186-71 INSTRUCTION (Read This First) (ARABIC, PERSIAN) (E)
2-681-186-81 INSTRUCTION (Read This First) (KOREAN) (KR, JE)
2-689-105-11 INSTRUCTION (Read This First) (HUNGARIAN, SLOVAK,
SWEDISH, FINNISH) (AEP)
2-689-105-21 INSTRUCTION (Read This First) (POLISH, CZECH,
NORWEGIAN, DANISH) (AEP)
2-681-187-01 INSTRUCTION (User’s Guide/Troubleshooting)
(JAPANESE) (J)
2-681-187-11 INSTRUCTION (User’s Guide/Troubleshooting)
(ENGLISH) (EXCEPT CH, KR, J)
2-681-187-21 INSTRUCTION (User’s Guide/Troubleshooting)
(FRENCH, ITALIAN) (CND, AEP)
2-681-187-31 INSTRUCTION (User’s Guide/Troubleshooting)
(SPANISH, PORTUGUESE) (AEP, E, JE)
2-681-187-41 INSTRUCTION (User’s Guide/Troubleshooting)
(GERMAN, DUTCH) (AEP)
2-681-187-51 INSTRUCTION (User’s Guide/Troubleshooting)
(TRADITIONAL CHINESE, SIMPLIFIED CHINESE)
(E, HK, CH, TW, JE)
2-681-187-61 INSTRUCTION (User’s Guide/Troubleshooting)
(RUSSIAN) (AEP)
2-681-187-71 INSTRUCTION (User’s Guide/Troubleshooting)
(ARABIC, PERSIAN) (E)
2-681-187-81 INSTRUCTION (User’s Guide/Troubleshooting)
(KOREAN)(KR, JE)
Ver. 1.3 2007.10
The changed portions from
Ver. 1.2 are shown in blue.
Ver. 1.2 are shown in blue.
Note: This item is supplied with the unit as an accessory, but
is not prepared as a service part.
