Read Sony DSC-WX1 (serv.man3) Service Manual online
1-5
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DSC-WX1_L2
1-5-3. Self-diagnosis Code Table
C
C
E
E
E
E
E
E
E
E
E
Block
Function
1
3
3
2
6
1
6
1
6
2
6
2
6
2
6
2
6
2
9
1
9
2
Detailed
Code
0
1
0
1
0
0
1
0
0
2
1
0
1
1
1
2
2
0
0
1
0
0
Symptom/State
The internal memory has experienced a
media error.
The internal memory has experienced a
format error.
format error.
“Memory Stick Duo” is unformatted.
“Memory Stick Duo” is broken.
“Memory Stick Duo” type error
The camera cannot read or write data
on the “Memory Stick Duo”.
on the “Memory Stick Duo”.
Trouble with hardware
Difficult to adjust focus
(Cannot initialize focus)
(Cannot initialize focus)
Zoom operations fault
(Cannot initialize zoom lens.)
(Cannot initialize zoom lens.)
Abnormality of IC for steadyshot.
Lens initializing failure.
Lens overheating (PITCH).
Lens overheating (YAW).
Abnormality of thermistor.
Abnormality when flash is being charged.
Non-standard battery is used.
Self-diagnosis Code
Repaired b
y:
Correction
Turn the power off and on again.
Format the internal memory.
Format the “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Insert a supported “Memory Stick Duo”.
Turn the power off and on again, or taking out and inserting the
“Memory Stick Duo” several times.
“Memory Stick Duo” several times.
Turn the power off and on again.
Retry turn the power on by the power switch. If it does not
recover, check the focus reset sensor of lens block (pin rf of
CN401 on the SY-233 board). If it is OK, check the focus motor
drive IC (IC402 on the SY-233 board).
recover, check the focus reset sensor of lens block (pin rf of
CN401 on the SY-233 board). If it is OK, check the focus motor
drive IC (IC402 on the SY-233 board).
Retry turn the power on by the power switch. Check the zoom
reset sensor of lens block (pin ra of CN401 on the SY-233
board), if zooming is performed when the zoom lever is
operated. If it is OK, check the zoom motor drive IC (IC402 on
the SY-233 board).
reset sensor of lens block (pin ra of CN401 on the SY-233
board), if zooming is performed when the zoom lever is
operated. If it is OK, check the zoom motor drive IC (IC402 on
the SY-233 board).
Check or replacement of the IC for steadyshot (IC402 on the SY-
233 board).
233 board).
Check or replacement of the IC for steadyshot (IC402 on the SY-
233 board).
233 board).
Check the HALL element (PITCH) of optical image stabilizer
(pin qf, qh of CN401 on the SY-233 board). If it is OK, check
PITCH/YAW angular velocity sensor (SE403 on the SY-233
board) peripheral circuits.
(pin qf, qh of CN401 on the SY-233 board). If it is OK, check
PITCH/YAW angular velocity sensor (SE403 on the SY-233
board) peripheral circuits.
Check the HALL element (YAW) of optical image stabilizer (pin
qj
qj
, ql of CN401 on the SY-233 board). If it is OK, check
PITCH/YAW angular velocity sensor (SE403 on the SY-233
board) peripheral circuits.
board) peripheral circuits.
Check the OIS temp sensor of optical image stabilizer (pin qa,
qs
qs
of CN401 on the SY-233 board).
Checking of ST-221 board or replacement of ST-221 board.
(Note)
(Note)
Use the compatible battery only.
Note:
After repair, be sure to perform “1-6. PROCESS AFTER FIXING FLASH ERROR”.
Click on the first or last page to see other DSC-WX1 (serv.man3) service manuals if exist.