Read Sony DSC-W690 Service Manual online
6-1
DSC-W690_L3
6. SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS.
(In addition to this, the necessary note is printed in each block.)
(In addition to this, the necessary note is printed in each block.)
For Schematic Diagrams
• All capacitors are in
• All capacitors are in
μF unless otherwise noted. pF : μ μF. 50
V or less are not indicated except for electrolytics and tantal-
ums.
ums.
• Chip resistors are 1/10 W unless otherwise noted.
k
k
Ω=1000 Ω, MΩ=1000 kΩ.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum capacitor,
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum capacitor,
Because it is damaged by the heat.
• Some chip part will be indicated as follows.
Example
Example
C541
L452
22U
10UH
TA
A
2520
Kinds of capacitor External dimensions (mm)
Case size
• Constants of resistors, capacitors, ICs and etc with XX indicate
Case size
• Constants of resistors, capacitors, ICs and etc with XX indicate
that they are not used.
In such cases, the unused circuits may be indicated.
• Parts with ★ differ according to the model/destination.
Refer to the mount table for each function.
• All variable and adjustable resistors have characteristic curve
• Parts with ★ differ according to the model/destination.
Refer to the mount table for each function.
• All variable and adjustable resistors have characteristic curve
B, unless otherwise noted.
• Signal name
XEDIT
XEDIT
→ EDIT PB/XREC
→ PB/REC
•
: non flammable resistor
•
: fusible resistor
•
: panel designation
•
: B+ Line
•
: B– Line
•
: IN/OUT direction of (+, –) B LINE.
•
: adjustment for repair.
For Printed Wiring Boards
•
•
: Uses unleaded solder.
•
: Circuit board
: Flexible board
Pattern from the side which enables seeing.
: pattern of the rear side
(The other layers’ patterns are not indicated)
• Through hole is omitted.
• There are a few cases that the part printed on diagram isn’t
• Through hole is omitted.
• There are a few cases that the part printed on diagram isn’t
mounted in this model.
•
: panel designation
• Chip parts.
Transistor Diode
Transistor Diode
2
1
3
2
1
3
2
1
3
3
4
5
2
1
1
2
3
6
5
4
E
B
C
3
1
5
2
4
6
1
2
3
6
5
4
3
1
5
2
4
6
1
2
3
5
4
4 3
1
2
3
1 2
4
5
5
3 4
1
2
1
4
2
3
4
6
2
5
3
1
1
2
4
3
1
4
2
3
Precautions for Replacement of Imager
• If the imager has been replaced, carry out all the adjustments
• If the imager has been replaced, carry out all the adjustments
for the camera section.
• As the imager may be damaged by static electricity from its
structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with dusts
nor exposed to strong light.
When indicating parts by reference num-
ber, please include the board name.
ber, please include the board name.
The components identified by mark
or dotted line with mark are critical
for safety.
Replace only with part number speci-
fied.
Les composants identifiés par une mar-
que sont critiques pour la sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
or dotted line with mark are critical
for safety.
Replace only with part number speci-
fied.
Les composants identifiés par une mar-
que sont critiques pour la sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
Click on the first or last page to see other DSC-W690 service manuals if exist.