DSC-W580 (serv.man2) - Sony Digital Camera Service Manual (repair manual)

dsc-w580 (serv.man2) service manual
Model
DSC-W580 (serv.man2)
Pages
21
Size
7.1 MB
Type
PDF
Document
Service Manual
Brand
Device
Digital Camera / LEVEL 2
File
dsc-w580-sm2.pdf
Date

Read Sony DSC-W580 (serv.man2) Service Manual online

DSC-W580_L2
Sony Corporation
SERVICE MANUAL
Revision History
SERVICE  NOTE (Check the following note before the service.)
LEVEL 
2
Published by Sony Techno Create Corporation
983454634.pdf
Ver. 1.3  2012.06
DIGITAL STILL CAMERA
The components identified by 
mark 
0 or dotted line with mark 
0 are critical for safety.
Replace only with part number 
specified.
Les composants identifiés par 
une marque 
0 sont critiques pour 
la sécurité.
Ne les remplacer que par une piè-
ce portant le numéro spécifié.
Canadian Model
AEP Model
UK Model
E Model
Korea Model
Photo: Black
9-834-546-34
DSC-W580
Ver.
Date
History
Contents
S.M. Rev.
issued
1.0
2010.12
Official Release
1.1
2011.07
Revised-1
(A1 11-039)
•  Revision of SERVICE NOTE.
 Page 
1-3
Yes
1.2
2011.09
Revised-2
(A2 11-204)
・ Correction of Model information table.
 Page 
Yes
1.3
2012.06
Revised-3
(A3 12-142)
・ Correction of REPAIR PARTS LIST.
 Page 
2-3
,
 2-4
,
 2-5
,
 2-7 
Yes
2012F08-1
  © 2012.06
– ENGLISH –
1-1.  Notes on Using Tripod Adapter
1-2.  PRECAUTION ON REPLACING THE SY-274 BOARD
1-3.  METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
1-4.  HOW TO WRITE DATA TO INTERNAL MEMORY
1-5. SELF-DIAGNOSIS 
FUNCTION
1-6.  PROCESS AFTER FIXING FLASH ERROR
1-7.  ORNAMENTAL RING A OR BARRIER ASSY REPLACING METHOD
1-8.  OPTICALSTEPPING MOTOR (F1430) REPLACING METHOD
1-9.  DC MOTOR WORM (A) BLOCK ASSY REPLACING METHOD
1-10. TWO TUBE LIBRICATING BLOCK ASSY AND GROUP 1 FRAME REPLACING 
METHOD
1-11. FINAL INSPECTION 
Internal memory
ON BOARD
Internal memory
ON BOARD
Revised-3
Replace the previously issued
SERVICE MANUAL 9-834-546-33
with this Manual.
DSC-W580_L2
– 2 –
SPECIFICATIONS
Camera 
[System] 
Image device: 7.75 mm (1/2.3 type)
color CCD, Primary color filter
Total pixel number of camera:
Approx. 16.4 Megapixels
Effective pixel number of camera:
Approx. 16.1 Megapixels
Lens: Carl Zeiss Vario-Tessar 5× zoom lens
f = 4.5 mm – 22.5 mm (25 mm –125 mm 
(35 mm film equivalent))
F2.6 (W) – F6.3 (T)
While shooting movies (16:9): 
28 mm – 140 mm
While shooting movies (4:3): 
34 mm – 170 mm
SteadyShot: Optical
Exposure control: Automatic exposure,
Scene Selection (12 modes)
White balance: Automatic, Daylight,
Cloudy, Fluorescent 1/2/3,
Incandescent, Flash, One Push
Underwater White Balance: Auto, 
Underwater 1/2, One Push
Recording interval for Burst mode:
Approx. 1.0 second
File format:
Still images: JPEG (DCF Ver. 2.0,
Exif Ver. 2.3, MPF Baseline)
compliant, DPOF compatible
Movies: MPEG-4 Visual
Recording media: Internal Memory
(Approx. 27 MB), “Memory Stick
Duo” media, SD cards
Flash: Flash range (ISO sensitivity 
(Recommended Exposure Index) set to Auto):
Approx. 0.2 m to 3.7 m (W) 
(7 7/8 inches to 12 feet 1 3/4 inches)
Approx. 1.0 m to 1.5 m (T) 
(3 feet 3 3/8 inches to 4 feet 11 1/8 inches)
[Input and Output connectors]
Multi use terminal: Type3a
(AV-out (SD/HD Component)/
USB/DC-in):
Video output
Audio output (Monaural)
USB communication
USB communication: Hi-Speed USB
(USB 2.0)
[LCD screen]
LCD panel: 
7.5 cm (3.0 type) TFT drive
Total number of dots: 
230 400 (960 × 240) dots
[Power, general]
Power: Rechargeable battery pack 
NP-BN1, 3.6 V
AC-LS5 AC Adaptor (sold 
separately), 4.2 V
Power consumption (during shooting): 
1.1 W
Operating temperature: 
0°C to 40°C (32°F to 104°F)
Storage temperature: 
–20°C to +60°C (–4°F to +140°F)
Dimensions:
94.0 mm × 56.0 mm × 19.1 mm 
(3 3/4 inches × 2 1/4 inches × 25/32 inches)
(W/H/D, excluding protrusions)
Mass (including NP-BN1 battery pack, 
“Memory Stick Duo” media):
Approx. 127 g (4.5 oz)
Microphone: Monaural
Speaker: Monaural
Exif Print: Compatible
PRINT Image Matching III: 
Compatible
BC-CSN/BC-CSNB battery
charger
Power requirements: AC 100 V to
240 V, 50/60 Hz, 2 W
Output voltage: DC 4.2 V, 0.25 A
Operating temperature: 
0°C to 40°C (32°F to 104°F)
Storage temperature: 
–20°C to +60°C (–4°F to +140°F)
Dimensions: 
Approx. 55mm × 24mm × 83mm
(2 1/4 inches × 31/32 inches × 3 3/8 inches) 
(W/H/D)
Mass: Approx. 55 g (1.9 oz)
Rechargeable battery pack
NP-BN1
Used battery: Lithium-ion battery
Maximum voltage: DC 4.2 V
Nominal voltage: DC 3.6 V
Maximum charge voltage: DC 4.2 V
Maximum charge current: 0.9 A
Capacity:
typical: 2.3 Wh (630 mAh)
minimum: 2.2 Wh (600 mAh)
Design and specifications are subject to
change without notice.
SAFETY-RELATED  COMPONENT  WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH 
MARK 
0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST 
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS 
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY 
SONY. 
ATTENTION AU  COMPOSANT  AYANT  RAPPORT 
À  LA  SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES 
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT 
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT 
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES 
SUPPLÉMENTS PUBLIÉS PAR SONY.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
UNLEADED SOLDER
This unit uses unleaded solder.
Boards requiring use of unleaded solder are printed with the lead free 
mark (LF) indicating the solder contains no lead.
(Caution:  Some printed circuit boards may not come printed with the 
lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
•   Set the soldering iron tip temperature to 350 °C approximately. 
If cannot control temperature, solder/unsolder at high temperature 
for a short time.
Caution:  The printed pattern (copper foil) may peel away if the 
heated tip is applied for too long, so be careful!  
Unleaded solder is more viscous (sticky, less prone to 
flow) than ordinary solder so use caution not to let solder 
bridges occur such as on IC pins, etc.
•   Be sure to control soldering iron tips used for unleaded solder and 
those for leaded solder so they are managed separately. Mixing un-
leaded solder and leaded solder will cause detachment phenomenon.
SAFETY  CHECK-OUT
After correcting the original service problem, perform the following 
safety checks before releasing the set to the customer.
1.  Check the area of your repair for unsoldered or poorly-soldered 
connections. Check the entire board surface for solder splashes and 
bridges.
2.  Check the interboard wiring to ensure that no wires are “pinched” 
or contact high-wattage resistors.
3.  Look for unauthorized replacement parts, particularly transistors, 
that were installed during a previous repair. Point them out to the 
customer and recommend their replacement.
4.  Look for parts which, through functioning, show obvious signs of 
deterioration. Point them out to the customer and recommend their 
replacement.
5.  Check the B+ voltage to see it is at the values specified.
6.  Flexible Circuit Board Repairing
 
•   Set the soldering iron tip temperature to 350 °C approximately.
 
•   Do not touch the soldering iron on the same conductor of the circuit 
board (within 3 times).
 
•   Be careful not to apply force on the conductor when soldering or 
unsoldering.
Model information table
Model
DSC-W580
Destination
CND, E, KR
UK
AEP, E
Color system
NTSC
PAL
PAL
TransferJet
• Abbreviation
  CND :  Canadian model
  KR :  Korea model
Ver. 1.2 2011.09
DSC-W580_L2
1-1
1. SERVICE  NOTE
1-1.  Notes on Using Tripod Adaptor
This model uses a Tripod Adaptor for adjustments.
When using a Tripod Adaptor, alter the USB, A/V cable for multi-use terminal as shown in the figure below.
1-2.  PRECAUTION ON REPLACING THE SY-274 BOARD
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATION DATA WRITE”.
RESTORE DATA
When you replace to the repairing board, get the data from the former one.
Start the Adjust Manual in the Adjust Station and perform “RESTORE DATA” to get the data. 
The data getting for this model is as follows.
• USB SERIAL No.
• Angular Velocity Sensor Sensitivity adjustment
• AWB standard data input & check, Color reproduction check
Note: When you cannot read data from the former replace the same time SY-274 board and lens.
Regarding the PMB Portable
PMB Portable has been written in internal memory.
SY-274 board for service is supplied with written the PMB Portable.
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB SERIAL No. INPUT”.
Angular Velocity Sensor
When you replace to the reparing board, write down the sensitivity displayed on the angular velocity sensor (SE401).
Start the Adjust Manual in the Adjust Station and execute the “Angular velocity sensor sensitivity adj”.
SY-274 BOARD (SIDE B)
SE401
PPP: PITCH sensor
sensitivity
YYY: YAW sensor
sensitivity
PP
YY
Note: The sensor sensitivity of SE401 of SY-274 board is written only repair parts.
– ENGLISH –
1-3.  METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
The data can be copied/erased by the operations on the HOME screen. (When erasing the data, execute formatting the internal memory.)
Note 1:When replacing the SY-274 board, erase the data in internal memory of the board before replacement.
Note 2:When replacing the SY-274 board, execute formatting and initialize the internal memory after replacement.
Method for Copying the Data in Internal Memory
Copy
Copies all images in the internal memory to a memory card. 
1. Insert a memory card with sufficient free capacity into the camera. 
2. MENU 
 
 (Settings) 
 
 (Memory Card Tool) 
 [Copy] 
 [OK] 
 
Notes
Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little 
remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the 
data. 
Images cannot be copied individually. 
The original images in the internal memory are retained even after copying. To delete the 
contents of the internal memory, remove the memory card after copying, then format the internal 
memory ([Format] in [Internal Memory Tool]). 
A new folder is created on the memory card and all the data will be copied to it. You cannot 
choose a specific folder and copy images to it. 
Method for Formatting the Internal Memory or “Memory Stick Duo” media
Format 
Formats the memory card or the internal memory. When you use a memory card with this camera for 
the first time, it is recommended to format the card using the camera for stable performance of the 
memory card before shooting. Note that formatting permanently erases all data on the memory card, 
and is unrecoverable. Save precious data on a computer, etc. 
1. MENU 
 
 (Settings) 
 
 (Memory Card Tool) or 
 (Internal Memory Tool) 
 
[Format]  
[OK]  
Note 
Note that formatting permanently erases all data including even protected images. 
DSC-W580_L2
1-2
– ENGLISH –
1-4.  HOW TO WRITE DATA TO INTERNAL MEMORY
Usually, the camera has been set so as to disable the data writing from the PC to the internal memory of the camera.
This setting must be changed temporarily when the data is to be written to the internal memory such as a case after the board replacement.
To change settings is enabled with using the writing enabler tool (Write Enable Tool) on the Adjust Manual is activating from the Adjust Station.
Data writing method
1)  Start the Adjust Manual from the Adjust Station.
2) Click 
 (Write Enable Tool) button.
3)  Click “Activate Write Enable Mode” button.
4)  Upon completion of the setting change, the following message will be displayed.
5)  Return the driver to the original one, and connect the PC to the camera (USB mode: Mass Storage).
6)  Write the data read out into the PC to the internal memory of the camera.
7)  Disconnect the PC from the camera, and turn off the camera.
Note: By turning off the camera, the write enable setting is reset.
1-5. SELF-DIAGNOSIS FUNCTION
1-5-1. Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis func-
tion starts working, and displays on the LCD screen what to do.
Details of the self-diagnosis functions are provided in the Instruction 
manual.
1-5-2. Self-diagnosis Display
When problems occur while the unit is operating, the LCD screen shows 
a 4-digit display consisting of an alphabet and numbers, whichblinks at 
3.2 Hz. This 5-character display indicates the “repaired by:”, “block” in 
which the problem occurred, and “detailed code” of the problem.
0 0
3 2
C
Repaired by:
Refer to “1-5-3. Self-diagnosis Code Tabl e”.
Indicates the appropriate
step to be taken.
E.g.
13 ....Format the “memory card”.
32 ....Turn on power again.
Block
Detailed Code
Blinks at 3.2 Hz
C : Corrected by customer
E : Corrected by service
engineer
LCD screen
0 0
3 2
C
Repaired by:
Refer to “1-5-3. Self-diagnosis Code Tabl e”.
Indicates the appropriate
step to be taken.
E.g.
13 ....Format the “memory card”.
32 ....Turn on power again.
Block
Detailed Code
Blinks at 3.2 Hz
C : Corrected by customer
E : Corrected by service
engineer
LCD screen
Page of 21

Download Sony DSC-W580 (serv.man2) Service Manual (Repair Manual)

Here you can read online and download Sony DSC-W580 (serv.man2) Service Manual in PDF. DSC-W580 (serv.man2) service manual will guide through the process and help you recover, restore, fix, disassemble and repair Sony DSC-W580 (serv.man2) Digital Camera. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.