DSC-W30 - Sony Digital Camera Service Manual (repair manual)

dsc-w30 service manual
Model
DSC-W30
Pages
31
Size
1.78 MB
Type
PDF
Document
Service Manual
Brand
Device
Digital Camera / BRAZIL LEVEL 3
File
dsc-w30.pdf
Date

Read Sony DSC-W30 Service Manual online

MANUAL DE SERVIÇO
LEVEL
 
3
Link
Instruções de
Acrobat Reader
Sony EMCS Co. - Sony Brasil Ltda
Memória Interna
na placa
DIAGRAMAS ESQUEMÁTICOS
PLACAS DE CIRCUITO IMPRESSO
NOTA DE SERVIÇO
LISTA DE PEÇAS PARA REPARO
DIGITAL STILL CAMERA
  © 2006.04
Publicado por Engenharia da Qualidade
Ver 1.0  2006.04
Brazilian Model
DSC-W30
Foto: DSC-W30/Prata
Os componentes identificados
com a marca 0 são críticos
para a segurança. Somente os
subistitua por peças especi-
ficadas nesse manual.
9-890-033-11
— 3 —
DSC-W30_L3
1.
Check the area of your repair for unsoldered or poorly-soldered
connections.  Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair.  Point
them out to the customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs
of deterioration.  Point them out to the customer and
recommend their replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
 : LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40
°
C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°
C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
VERIFICAÇÃO GERAL DE SEGURANÇA
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 
0
 OR DOTTED LINE WITH
MARK 
0
 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 
0
 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CAUTION :
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
— 3 —
DSC-W30_L3
INDICE
1. NOTA DE SERVIÇO
1-3. Metodo para Copiar ou Apagar os dados da Memória
Interna··············································································· 1-2
4. PLACAS DE CIRCUITO IMPRESSO E 
DIAGRAMAS ESQUEMÁTICOS
4-2. Diagramas Esquemáticos·················································· 4-3
4-3. Placas de Circuito Impresso············································ 4-17
4-4. Localização das Peças Montadas···································· 4-25
5. LISTA DE PEÇAS PARA REPARO
5-2. Lista de Peças Elétricas···················································· 5-8
Seção
Título
Pag.
1-2
DSC-W30_L3
1-3. MÉTODO PARA A COPIAR OU APAGAR O DADO DA MEMÓRIA INTERNA
The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.)
Note 1:
When replacing the SY-143 board, erase the data in internal memory of the board before replacement.
Note 2:
When replacing the SY-143 board or the IC202 on the SY-143 board, execute formatting and initialize the internal memory after
replacement.
Method for Copying the Data in Internal Memory
Method for Formatting the Internal Memory
Copies all images in the internal memory to a “Memory Stick Duo”.
1 Insert a “Memory Stick Duo” having 32 MB or larger capacity.
2 Select [OK] with v on the control button, then press z.
The message “All data in internal memory will be copied Ready?” appears.
3 Select [OK] with v, then press z.
Copying starts. 
• Use a fully charged battery pack or the AC Adaptor (not supplied). If you attempt to copy image files 
using a battery pack with little remaining charge, the battery pack may run out, causing copying to fail or 
possibly corrupting the data.
• You cannot copy individual images.
• The original images in the internal memory are retained even after copying. To delete the contents of the 
internal memory, remove the “Memory Stick Duo” after copying, then execute the [Format] command in 
(Internal Memory Tool).
• You cannot select a folder copied on a “Memory Stick Duo”.
• Even if you copy data, a 
 (Print order) mark is not copied.
Copy
OK
See the following procedure.
Cancel
Cancels the copying.
Copying
102_COPY
This item does not appear when a “Memory Stick Duo” is inserted in the camera.
The default settings are marked with 
.
Formats the internal memory.
• Note that formatting irrevocably erases all data in the internal memory, including even protected images.
1 Select [OK] with v on the control button, then press z.
The message “All data in internal memory will be erased Ready?” appears.
2 Select [OK] with v, then press z.
The format is complete.
Format
OK
See the following procedure.
Cancel
Cancels the formatting.
1. NOTA DE SERVIÇO
Page of 31
Display

Download Sony DSC-W30 Service Manual (Repair Manual)

Here you can read online and download Sony DSC-W30 Service Manual in PDF. DSC-W30 service manual will guide through the process and help you recover, restore, fix, disassemble and repair Sony DSC-W30 Digital Camera. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.