Read Sony DSC-W30 (serv.man2) Service Manual online
MANUAL DE SERVIÇO
LEVEL
2
Link
Instruções de
Acrobat Reader
Sony EMCS Co. - Sony Brasil Ltda
Memória Interna
na placa
NOTA DE SERVIÇO
ESPECIFICAÇÕES
FRAME DIGRAMA ESQUEMÁTICO
DIAGRAMAS EM BLOCO
DESMONTAGEM
PLACAS DE CIRCUITO IMPRESSO
LISTA DE PEÇAS PARA REPARO
DIAGRAMAS ESQUEMÁTICOS
Ver 1.0 2006.04
DIGITAL STILL CAMERA
© 2006.04
Publicado por Engenharia da Qualidade
Brazilian Model
Os componentes identificados
com a marca 0 são críticos
para a segurança. Somente os
subistitua por peças especi-
ficadas nesse manual.
com a marca 0 são críticos
para a segurança. Somente os
subistitua por peças especi-
ficadas nesse manual.
• Precaução em substituir a placa SY-143
DSC-W30
Foto: DSC-W30/Prata
9-890-033-31
— 2 —
DSC-W30_L2
ESPECIFICAÇÕES
Camera
[System]
Image device
7.18 mm (1/2.5 type) color
CCD, Primary color filter
CCD, Primary color filter
Total pixel number of camera
Approx. 6 183 000 pixels
Effective pixel number of camera
Approx. 6 003 000 pixels
Lens
Carl Zeiss Vario-Tessar
3
3
× zoom lens
f = 6.3 – 18.9 mm (38 –
114 mm when converted to a
35 mm still camera)
F2.8 – 5.2
114 mm when converted to a
35 mm still camera)
F2.8 – 5.2
Exposure control Automatic exposure, Scene
Selection (7 modes)
White balance
Automatic, Daylight, Cloudy,
Fluorescent, Incandescent,
Flash
Fluorescent, Incandescent,
Flash
File format (DCF compliant)
Still images: Exif Ver. 2.21
JPEG compliant, DPOF
compatible
Movies: MPEG1 compliant
(Monaural)
JPEG compliant, DPOF
compatible
Movies: MPEG1 compliant
(Monaural)
Recording media Internal Memory (32 MB)
“Memory Stick Duo”
Flash
Recommended distance (ISO
set to Auto): approx. 0.2 m to
4.2 m (7 7/8 inches to 13 feet
9 3/8 inches) (W)/approx.
0.3 m to 2.2 m (11 7/8 inches to
7 feet 2 5/8 inches) (T)
set to Auto): approx. 0.2 m to
4.2 m (7 7/8 inches to 13 feet
9 3/8 inches) (W)/approx.
0.3 m to 2.2 m (11 7/8 inches to
7 feet 2 5/8 inches) (T)
[Input and Output connectors]
A/V OUT jack (Monaural)
Minijack
Video: 1 Vp-p, 75
Video: 1 Vp-p, 75
Ω,
unbalanced, sync negative
Audio: 327 mV (at a 47 k
Audio: 327 mV (at a 47 k
Ω
load)
Output impedance 2.2 k
Output impedance 2.2 k
Ω
USB jack
mini-B
USB communication
Hi-Speed USB (USB 2.0
compliant)
compliant)
[LCD screen]
LCD panel
5.1 cm (2.0 type) TFT drive
Total number of dots
84 960 (354
×240) dots
[Power, general]
Power
Rechargeable battery pack NP-
BG1, 3.6 V
BG1, 3.6 V
AC-LS5K AC Adaptor (not
supplied), 4.2 V
supplied), 4.2 V
Power consumption (during shooting with the
LCD screen on)
1.0W
1.0W
Operating temperature
0 to 40
°C (32 to 104°F)
Storage temperature
–20 to +60
°C (–4 to +140°F)
Dimensions
89.8
×59.0×22.9 mm
(3 5/8 inches
× 2 3/8 inches ×
29/32 inches) (W/H/D,
excluding protrusions)
excluding protrusions)
Mass
DSC-W40
Approx. 186 g (6.6 oz)
(including NP-BG1 battery
pack and neck strap, etc.)
(including NP-BG1 battery
pack and neck strap, etc.)
DSC-W30
Approx. 153 g (5.4 oz)
(including NP-BG1 battery
pack and wrist strap, etc.)
(including NP-BG1 battery
pack and wrist strap, etc.)
Microphone
Electret condenser microphone
Speaker
Dynamic speaker
Exif Print
Compatible
PRINT Image Matching III
Compatible
PictBridge
Compatible
BC-CSG battery charger
Power requirements
AC 100 to 240 V, 50/60 Hz,
2 W
2 W
Output voltage
DC 4.2 V, 0.25 A
Operating temperature
0 to 40
°C (32 to 104°F)
Storage temperature
–20 to +60
°C (–4 to +140°F)
Dimensions
Approx. 62
× 24 × 91 mm
(2 1/2
× 31/32 ×3 5/8 inches)
(W/H/D)
Mass
Approx. 75 g (2.7 oz)
Rechargeable battery pack NP-BG1
Used battery
Lithium-ion battery
Maximum voltage
DC 4.2 V
Nominal voltage DC 3.6 V
Capacity
3.6 Wh (960 mAh)
Design and specifications are subject to change
without notice.
without notice.
— 3 —
DSC-W30_L2
1.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
connections. Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
of deterioration. Point them out to the customer and
recommend their replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40
• Unleaded solder melts at a temperature about 40
°
C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°
C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
VERIFICAÇÃO GERAL DE SEGURANÇA
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE WITH
MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE
0
SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CAUTION :
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
— 4 —
DSC-W30_L2
INDICE
1. NOTA DE SERVIÇO
1-1. Descrição sobre o Auto Diagnóstico Visualizado.············ 1-1
1-2. Processo Após o Reparo do Erro do Flash ······················· 1-1
1-3. Metodo para Copiar ou Apagar os dados da Memória
1-2. Processo Após o Reparo do Erro do Flash ······················· 1-1
1-3. Metodo para Copiar ou Apagar os dados da Memória
Interna················································································ 1-2
1-4. Precaução em substituir a placa SY-143 ··························· 1-3
2. DESMONTAGEM
2-1. Desmontagem··································································· 2-2
2-2. Método da troca da Grade Montada ································· 2-6
2-3. Método da troca da unidade do Motor do Zoom··············· 2-9
2-2. Método da troca da Grade Montada ································· 2-6
2-3. Método da troca da unidade do Motor do Zoom··············· 2-9
3. DIAGRAMAS EM BLOCO
3-1. Diagrama em Bloco Geral (1/2) ······································ 3-1
3-2. Diagrama em Bloco Geral (2/2) ······································ 3-2
3-3. Diagrama em Bloco Power ·············································· 3-3
3-2. Diagrama em Bloco Geral (2/2) ······································ 3-2
3-3. Diagrama em Bloco Power ·············································· 3-3
4. PLACAS DE CIRCUITO IMPRESSO E
DIAGRAMAS ESQUEMÁTICOS
4-1. Diagrama Esquemático Frame·········································· 4-1
4-2. Diagramas Esquemáticos·················································· 4-3
4-3. Placas de Circuito Impresso············································ 4-17
4-4. Localização das Peças Montadas···································· 4-26
4-2. Diagramas Esquemáticos·················································· 4-3
4-3. Placas de Circuito Impresso············································ 4-17
4-4. Localização das Peças Montadas···································· 4-26
5. LISTA DE PEÇAS PARA REPARO
5-1. Vistas Explodidas······························································ 5-2
5-2. Lista de Peças Elétricas····················································· 5-6
5-2. Lista de Peças Elétricas····················································· 5-6
Seção
Titulo
Pag.
