Read Sony DSC-W1 (serv.man2) Service Manual online
MANUAL DE SERVIÇO
LEVEL
2
Link
NOTA DE SERVIÇO
DESMONTAGEM
DIAGRAMAS EM BLOCOS
DIAGRAMA ESQUEMÁTICO DAS PLACAS
DIAGRAMAS ESQUEMÁTICOS
PLACAS DE CIRCUITO IMPRESSO
LISTA DE PEÇAS PARA REPARO
ESPECIFICAÇÕES
Link
Histórico de Revisão
DSC-W1
Acrobat Reader
Instruções de
Acrobat Reader
• For ADJUSTMENTS (SECTION 6), refer to SERVICE MANUAL, ADJ (9
890165
51.pdf).
• Reference No. search on printed wiring boards is available.
• Note in Lens Frame Installation
• Exchange Method of Barrier Assy
• HELP: Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
• Exchange Method of Barrier Assy
• HELP: Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
Ver 1.1 10.2004
DIGITAL STILL CAMERA
On the CH-146, SY-102, SW-422, MS-204, MS-205 flexible, JK-263 and SP-045 flexible boards
Schematic diagram ............... Pages 4-9 to 4-28
Printed wiring board .............. Pages 4-39 to 4-48
Mounted parts location .......... Pages 4-54 and 4-55
Electrical parts list ................. Pages 5-7 to 5-8
Printed wiring board .............. Pages 4-39 to 4-48
Mounted parts location .......... Pages 4-54 and 4-55
Electrical parts list ................. Pages 5-7 to 5-8
and 5-10 to 5-13
The above-described information is shown in
service manual Level 3.
service manual Level 3.
Brazilian Model
This service manual procides the information that is premised the
circuit board replacement service and not intended repair inside
the CH-146, SY-102, SW-422, MS-204, MS-205 flexible, JK-263
and SP-045 flexible boards.
Therefore, schematic diagram, printed wiring board and electrical
parts list of the CH-146, SY-102, SW-422, MS-204, MS-205
flexible, JK-263 and SP-045 flexible boards are not shown.
The following pages are not shown.
circuit board replacement service and not intended repair inside
the CH-146, SY-102, SW-422, MS-204, MS-205 flexible, JK-263
and SP-045 flexible boards.
Therefore, schematic diagram, printed wiring board and electrical
parts list of the CH-146, SY-102, SW-422, MS-204, MS-205
flexible, JK-263 and SP-045 flexible boards are not shown.
The following pages are not shown.
9-890-165-31
— 2 —
DSC-W1
ESPECIFICAÇÕES
x
Camera
[System]
Image device
9.04 mm (1/1.8 type) color CCD
Primary color filter
Primary color filter
Total pixels number of camera
Approx. 5 255 000 pixels
Effective pixels number of camera
Approx. 5 090 000 pixels
Lens
Carl Zeiss Vario-Tessar
3 zo om lens
f = 7.9 – 23.7 mm (38 – 114 mm when
converted to a 35 mm still camera)
F2.8 – 5.2
3 zo om lens
f = 7.9 – 23.7 mm (38 – 114 mm when
converted to a 35 mm still camera)
F2.8 – 5.2
Exposure control
Automatic exposure, Manual
exposure, Twilight, Twilight portrait,
Candle, Landscape, Beach, Soft snap
exposure, Twilight, Twilight portrait,
Candle, Landscape, Beach, Soft snap
White balance
Automatic, Daylight, Cloudy,
Fluorescent, Incandescent
Fluorescent, Incandescent
File format (DCF compliant)
Still images: Exif Ver. 2.2 JPEG
compliant, DPOF compatible
Movies: MPEG1 compliant
(Monaural)
compliant, DPOF compatible
Movies: MPEG1 compliant
(Monaural)
Recording media
“Memory Stick”
Flash
Recommended distance (ISO set to
Auto):
0.2 m to 3.5 m (7 7/8 inches to 11 feet
5 7/8 inches) (W)
0.3 m to 2.5 m (11 7/8 inches to 8 feet
2 1/2 inches) (T)
Auto):
0.2 m to 3.5 m (7 7/8 inches to 11 feet
5 7/8 inches) (W)
0.3 m to 2.5 m (11 7/8 inches to 8 feet
2 1/2 inches) (T)
[Input and Output connectors]
A/V OUT (MONO) jack (Monaural)
Minijack
Video: 1 Vp-p, 75
Video: 1 Vp-p, 75
Ω, unbalanced,
sync negative
Audio: 327 mV (at a 47 k
Audio: 327 mV (at a 47 k
Ω load)
Output impedance 2.2 k
Ω
USB jack
mini-B
USB communication
Hi-Speed USB (USB 2.0 compliant)
[LCD screen]
LCD panel
6.2 cm (2.5 type) TFT drive
Total number of dots
123 200 (560
×220) dots
[Power, general]
Power
AA Nickel-Metal Hydride batteries (2)
2.4 V
AC-LS5 AC Adaptor
(opcional), 4.2 V
2.4 V
AC-LS5 AC Adaptor
(opcional), 4.2 V
Power consumption (during shooting with
LCD screen on)
LCD screen on)
1.4 W
Operating temperature
0
°C to +40°C (+32°F to +104°F)
Storage temperature
–20
°C to +60°C (–4°F to +140°F)
Dimensions
91
× 60 × 32.9 mm
(3 5/8
× 2 3/8 × 1 5/16 inches)
(W/H/D, excluding maximum
protrusions)
protrusions)
Mass
Approx. 250 g (8.8 oz) (including two
batteries, “Memory Stick” and wrist
strap)
batteries, “Memory Stick” and wrist
strap)
Microphone
Electret condenser microphone
Speaker
Dynamic speaker
Exif Print
Compatible
PRINT Image Matching II
Compatible
PictBridge
Compatible
x
BC-CS2A/CS2B Ni-MH battery
charger
charger
Power requirements
AC 100 to 240V 50/60Hz
3 W
3 W
Output voltage
AA : DC 1.4 V 400 mA
× 2
AAA : DC 1.4 V 160 mA
× 2
Operating temperature range
0
°C to +40°C (+32°F to +104°F)
Storage temperature range
–20
°C to +60°C (–4°F to +140°F)
Dimensions
71
× 30 × 91 mm
(2 7/8
× 1 3/16 × 3 5/8 inches) (W/H/D)
Mass
Approx. 90 g (3 oz)
x
AC-LS5 AC Adaptor (opcional)
Input rating
100 V to 240 V AC, 50/60 Hz, 11 W,
0.16 A to 0.09 A
0.16 A to 0.09 A
Output rating
4.2 V DC, 1.5 A
Operating temperature
0
°C to +40°C (+32°F to +104°F)
Storage temperature
–20
°C to +60°C (–4°F to +140°F)
Dimensions
Approx. 48
× 29 × 81mm
(1 15/16
× 1 3/16 × 3 1/4 inches)
(W/H/D, excluding projecting parts)
Mass
Approx. 130 g (5 oz)
x
Accessories
• HR6 (size AA) Ni-MH batteries (DSC-W1: 2,
DSC-W12: 4)
• Battery case (DSC-W1: 1, DSC-W12: 2)
• BC-CS2A/CS2B Ni-MH Battery charger (1)
• Power cord (mains lead) (1)
• USB cable (1)
• A/V connecting cable (1)
• Wrist strap (1)
• “Memory Stick” (32 MB) (1)
• CD-ROM (USB driver SPVD-012) (1)
• Operating instructions (1)
• BC-CS2A/CS2B Ni-MH Battery charger (1)
• Power cord (mains lead) (1)
• USB cable (1)
• A/V connecting cable (1)
• Wrist strap (1)
• “Memory Stick” (32 MB) (1)
• CD-ROM (USB driver SPVD-012) (1)
• Operating instructions (1)
See page 5-15.
Design and specifications are subject to change
without notice.
without notice.
— 3 —
DSC-W1
1.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
connections. Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
of deterioration. Point them out to the customer and
recommend their replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40
• Unleaded solder melts at a temperature about 40
°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE WITH
MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE
0
SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
— 4 —
DSC-W1
TABLE OF CONTENTS
1.
SERVICE NOTE
1-1.
Note for Repair ································································ 1-1
1-2.
Discharging of the ST-101 Flexible Board’s Charging
Capacitors (C102 and C103) ··········································· 1-1
Capacitors (C102 and C103) ··········································· 1-1
1-3.
Note in Lens Frame Installation ······································ 1-2
1-4.
Description on Self-diagnosis Display ···························· 1-2
2.
DISASSEMBLY
2-1.
Flow Chart ······································································· 2-1
2-2.
SY-102 Board Service Position ······································· 2-3
2-3.
Exchange Method of Barrier Assy ·································· 2-5
2-3-1. Peel Off Old Ornamental Ring A ···································· 2-5
2-3-2. Remove Old Barrier Assy ················································ 2-6
2-3-3. Install New Barrier Assy ················································· 2-6
2-3-4. Adhere the Ornamental Ring A ······································· 2-7
2-4.
2-3-2. Remove Old Barrier Assy ················································ 2-6
2-3-3. Install New Barrier Assy ················································· 2-6
2-3-4. Adhere the Ornamental Ring A ······································· 2-7
2-4.
Circuit Boards Location ·················································· 2-8
3.
BLOCK DIAGRAMS
3-1.
Overall Block Diagram (1/2) ··········································· 3-1
3-2.
Overall Block Diagram (2/2) ··········································· 3-3
3-3.
Power Block Diagram (1/2) ············································· 3-5
3-4.
Power Block Diagram (2/2) ············································· 3-7
4.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
SCHEMATIC DIAGRAMS
4-1.
Frame Schematic Diagram ·············································· 4-1
4-2.
Schematic Diagrams ························································ 4-5
CD-507 FLEXIBLE (CCD IMAGER) ···························· 4-7
ST-100 (FLASH DRIVE) ·············································· 4-29
ST-101 FLEXIBLE
(CHARGING CAPACITOR, FLASH UNIT) ··············· 4-29
US-011 FLEXIBLE (USB CONNECTOR) ·················· 4-31
CONTROL SWITCH BLOCK ····································· 4-32
CD-507 FLEXIBLE (CCD IMAGER) ···························· 4-7
ST-100 (FLASH DRIVE) ·············································· 4-29
ST-101 FLEXIBLE
(CHARGING CAPACITOR, FLASH UNIT) ··············· 4-29
US-011 FLEXIBLE (USB CONNECTOR) ·················· 4-31
CONTROL SWITCH BLOCK ····································· 4-32
4-3.
Printed Wiring Boards ··················································· 4-35
CD-507 FLEXIBLE ······················································ 4-37
ST-100 ··········································································· 4-49
ST-101 FLEXIBLE ······················································· 4-50
US-011 FLEXIBLE ······················································· 4-51
CD-507 FLEXIBLE ······················································ 4-37
ST-100 ··········································································· 4-49
ST-101 FLEXIBLE ······················································· 4-50
US-011 FLEXIBLE ······················································· 4-51
4-4.
Mounted Parts Location ················································ 4-53
5.
REPAIR PARTS LIST
5-1.
Exploded Views ······························································· 5-2
5-1-1. Cabinet Block Section ····················································· 5-2
5-1-2. Main Block Section ························································· 5-3
5-1-3. Lens Block Section ·························································· 5-4
5-1-4. Side Frame Block Section ··············································· 5-5
5-2.
5-1-2. Main Block Section ························································· 5-3
5-1-3. Lens Block Section ·························································· 5-4
5-1-4. Side Frame Block Section ··············································· 5-5
5-2.
Electrical Parts List ························································· 5-6
Section
Title
Page
