Read Sony DSC-T5 (serv.man4) Service Manual online
6-16
DSC-T5_ADJ
1-4-3.
Adjusting Method
1.
Wide Limit Adjustment
Adjustment to remove variations at the wide end of the inner fo-
cus lens.
cus lens.
Adjustment Page
6F
Adjustment Address
18, 19
1-1. Adjusting method when the lens is replaced:
Adjusting method:
Order Page Address
Data
Procedure
1
00
01
01
Set the data.
2
40
38
00
Set the data.
3
6F
18
Set the data. (Note)
4
6F
19
Set the data. (Note)
5
7C
16
01
t 00
Change the data.
(The data is OK if it is “00”.)
(The data is OK if it is “00”.)
6
Save the data.
7
80
34
Check the data is “00”.
8
80
30
Check the data is “00”.
9
Perform “Flange Back
Adjustment”.
Adjustment”.
Note:
The data of page: 6F, address: 18 and 19, that are set in the
Orders 2 and 3 as described above, are shown on the data
sheet supplied with the replacement lens for repair.
sheet supplied with the replacement lens for repair.
Set the upper single byte of the 2-byte data shown on the
sheet to address: 18, and the lower byte of the data to the
address: 19.
address: 19.
Fig. 6-1-17
1-2. Adjusting method when replacement of lens
is not required and the SY-134 board is replaced:
is not required and the SY-134 board is replaced:
When the data of page: 6F, address: 18 and 19 can be
read from the defective SY-134 board before replace-
ment, and both of the data are not “00”:
read from the defective SY-134 board before replace-
ment, and both of the data are not “00”:
Adjusting method:
Order Page Address
Data
Procedure
1
00
01
01
Set the data.
2
40
38
00
Set the data.
3
6F
18
Set the previous data
4
6F
19
Set the previous data
5
7C
16
01
t 00
Change the data.
(The data is OK if it is “00”.)
(The data is OK if it is “00”.)
6
Save the data.
7
80
34
Check the data is “00”.
8
80
30
Check the data is “00”.
9
Perform “Flange Back
Adjustment”.
Adjustment”.
When the data of the page: 6F, address: 18 and 19 can
be read out from the defective SY-134 board before
replacing it, and both of the data are “00”:
be read out from the defective SY-134 board before
replacing it, and both of the data are “00”:
1) Replace the lens with the replacement lens and perform “1-1.
Adjusting method when the lens is replaced”.
When the data of page: 6F, address: 18 and 19 cannot
be read from the defective SY-134 board:
be read from the defective SY-134 board:
1) Replace the lens with the replacement lens and perform “1-1.
Adjusting method when the lens is replaced”.
Note:
The data of page: 7C, address: 16, that is set in the Order 4
of the adjusting method of 1-1 or 1-2, is “01” when shipped
from the factory. Let the data remain “00” after comple-
tion of the service adjustment.
of the adjusting method of 1-1 or 1-2, is “01” when shipped
from the factory. Let the data remain “00” after comple-
tion of the service adjustment.
Data for Page: 6F, Address: 19
2-byte data
Data for Page: 6F, Address: 18
XXXX
Click on the first or last page to see other DSC-T5 (serv.man4) service manuals if exist.