Read Sony DSC-S950 Service Manual online
Revision History
Revision History
Sony EMCS Co.
DSC-S950
SERVICE MANUAL
Link
SERVICE NOTE
SPECIFICATIONS
BLOCK DIAGRAM
DISASSEMBLY
REPAIR PARTS LIST
Link
Internal memory
ON BOARD
Internal memory
ON BOARD
Ver. 1.2 2010.03
2010C0500-1
© 2010.3
Published by Tokai TEC
9-852-641-13
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
Hong Kong Model
Korea Model
Argentine Model
The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part num-
ber specified.
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part num-
ber specified.
Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
Photo: Silver
DIGITAL STILL CAMERA
DSC-S950
Revised-2
Replacement of the previously issued
SERVICE MANUAL 9-852-641-12
with this manual.
SERVICE MANUAL 9-852-641-12
with this manual.
— 2 —
DSC-S950
SPECIFICATIONS
Camera
[System]
Image device:
7.70 mm (1/2.3 type) color CCD, Primary
color filter
color filter
Total pixel number of camera:
Approx. 10.3 Megapixels
Effective pixel number of camera:
Approx. 10.1 Megapixels
Lens: 4× zoom lens f = 5.8 – 23.2 mm (33 –
132 mm (35 mm film equivalent)) F2.5 (W) –
5.6 (T)
5.6 (T)
Exposure control: Automatic exposure, Scene
Selection (7 modes)
White balance: Automatic, Daylight, Cloudy,
Fluorescent 1, 2, 3, Incandescent, Flash
File format (DCF compliant):
Still images: Exif Ver. 2.21 JPEG compliant,
DPOF compatible
Movies: AVI (Motion JPEG)
DPOF compatible
Movies: AVI (Motion JPEG)
Recording media: Internal Memory (approx.
12 MB), “Memory Stick Duo” media
Flash: Flash range (ISO sensitivity
(Recommended Exposure Index) set to Auto):
approx. 0.5 to 3.5 m (1 feet 7 3/4 inches to
11 feet 5 7/8 inches) (W)/approx. 0.5 to 1.5 m
(1 feet 7 3/4 inches to 4 feet 11 1/8 inches) (T)
approx. 0.5 to 3.5 m (1 feet 7 3/4 inches to
11 feet 5 7/8 inches) (W)/approx. 0.5 to 1.5 m
(1 feet 7 3/4 inches to 4 feet 11 1/8 inches) (T)
Recording interval of Burst:
Approx. 1.0 seconds
[Input and Output connectors]
(USB)•A/V OUT terminal:
Video, Audio (Monaural), USB
communication
communication
USB communication:
Hi-Speed USB (USB 2.0 compliant)
[LCD screen]
LCD panel: 6.7 cm (2.7 type) TFT drive
Total number of dots: 230 400 (960×240) dots
Total number of dots: 230 400 (960×240) dots
[Power, general]
Power: Rechargeable battery pack NP-BK1, 3.6 V
AC-LS5K AC Adaptor (sold separately),
4.2 V
4.2 V
Power consumption (during shooting):
1.2 W
Operating temperature: 0 to 40°C (32 to 104°F)
Storage temperature: –20 to +60°C (–4 to +140°F)
Dimensions: 93.1×55.7×23.8 mm (3 3/4×
Storage temperature: –20 to +60°C (–4 to +140°F)
Dimensions: 93.1×55.7×23.8 mm (3 3/4×
2 1/4×15/16 inches) (W/H/D, excluding
protrusions)
protrusions)
Mass: Approx. 157 g (5.5 oz) (including NP-BK1
battery pack and strap, etc.)
Microphone: Monaural
Speaker: Monaural
Exif Print: Compatible
PRINT Image Matching III: Compatible
Speaker: Monaural
Exif Print: Compatible
PRINT Image Matching III: Compatible
BC-CSK/BC-CSKA battery charger
Power requirements: AC 100 V to 240 V, 50/
60 Hz, 2.2 W (BC-CSK)/2.3 W (BC-CSKA)
Output voltage: DC 4.2 V, 0.33 A (BC-CSK)/
0.30 A (BC-CSKA)
Operating temperature: 0 to 40°C (32 to 104°F)
Storage temperature: –20 to +60°C (–4 to +140°F)
Dimensions: Approx. 62×24×91 mm (2 1/2×
Storage temperature: –20 to +60°C (–4 to +140°F)
Dimensions: Approx. 62×24×91 mm (2 1/2×
31/32×3 5/8 inches) (W/H/D)
Mass: Approx. 75 g (2.7 oz) (BC-CSK)/Approx.
70 g (2.5 oz) (BC-CSKA)
Rechargeable battery pack NP-
BK1
BK1
Used battery: Lithium-ion battery
Maximum output voltage: DC 4.2 V
Mean output voltage: DC 3.6 V
Maximum charge voltage: DC 4.2 V
Maximum charge current: 1.4 A
Capacity: Approx. 3.4 Wh (970 mAh)
Maximum output voltage: DC 4.2 V
Mean output voltage: DC 3.6 V
Maximum charge voltage: DC 4.2 V
Maximum charge current: 1.4 A
Capacity: Approx. 3.4 Wh (970 mAh)
Design and specifications are subject to change
without notice.
without notice.
PictBridge: Compatible
— 3 —
DSC-S950
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE WITH
MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
1.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
connections. Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
of deterioration. Point them out to the customer and
recommend their replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE
0
SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40
• Unleaded solder melts at a temperature about 40
°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Replace only with the same or equivalent type.
1-1E
DSC-S950
1-1. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.)
Note 1:
When replacing main board, erase the data in internal memory of the board before replacement.
Note 2:
When replacing main board, execute formatting and initialize the internal memory after replacement.
Method for Copying the Data in Internal Memory
Method for Formatting the Internal Memory
1. SERVICE NOTE
Copies all images in the internal memory to “Memory Stick Duo” media.
1
Insert “Memory Stick Duo” media having sufficient free capacity.
2
Select [Copy] with v/V on the control button, then press z.
The message “All data on internal memory will be copied” appears.
The message “All data on internal memory will be copied” appears.
3
Select [OK] with v, then press z.
Copying starts.
Copying starts.
To cancel copying
Select [Cancel] in step 3, then press z.
• Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little
remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data.
• You cannot select images to copy.
• The original images in the internal memory are retained even after copying. To delete the contents of the
internal memory, remove the “Memory Stick Duo” media after copying, then format the internal memory
([Format] in [Internal Memory Tool]).
([Format] in [Internal Memory Tool]).
• A new folder is created on the “Memory Stick Duo” media and all the data will be copied to it. You cannot
choose a specific folder and copy images to it.
• The
(Print order) marks on the images are not copied.
Copy
Fo
This item does not appear when “Memory Stick Duo” media is inserted in the camera.
rmats the internal memory.
• Note that formatting permanently erases all data in the internal memory, including even protected images.
1
Select [Format] with v/V on the control button, then press z.
The message “All data on internal memory will be erased” appears.
The message “All data on internal memory will be erased” appears.
2
Select [OK] with v, then press z.
Formatting starts.
Formatting starts.
To cancel formatting
Select [Cancel] in step 2, then press z.
Format
Ver. 1.1 2009.07
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
