Read Sony DSC-S600 (serv.man4) Service Manual online
6-20
DSC-S600_ADJ
1-6.
INITIALIZATION OF DATA
1.
Initializing All Page Data
By performing the following procedure, data of all pages will be
initialized.
initialized.
Note:
If all page data have been initialized, all adjustments need
to be performed again.
to be performed again.
Initializing Method:
1) Select page: 00, address: 01 and set data: 01.
2) Click [Sector Write] on the SEUS screen to display the SEUS
1) Select page: 00, address: 01 and set data: 01.
2) Click [Sector Write] on the SEUS screen to display the SEUS
SECTOR WRITE screen.
3) Check that the SET ID is “0A”.
4) Click [All] of the ALL SELECT buttons to select all pages.
4) Click [All] of the ALL SELECT buttons to select all pages.
(Fig. 6-1-44 A)
5) Click [Write] to write the initializing data to the flash memory
of the camera.
6) Wait for 3 sec.
7) Click [Close] to close the SEUS SECTOR WRITE screen.
8) Click [Save] on the SEUS screen.
9) Select page: 80, address: 34, and check that the data is “00”.
10) Select page: 80, address: 30, and check that the data is “00”.
11) Perform “Initial Language Data Check”.
7) Click [Close] to close the SEUS SECTOR WRITE screen.
8) Click [Save] on the SEUS screen.
9) Select page: 80, address: 34, and check that the data is “00”.
10) Select page: 80, address: 30, and check that the data is “00”.
11) Perform “Initial Language Data Check”.
Processing after Completing Initializing
Order Page Address
Data
Procedure
1
40
28
01 [Set]
(Note)
Note:
At this time, the camera is reset and the power is turns off
once and then on again. Accordingly, the SEUS goes in
“disconnect” state, but this is not a trouble. Click [Connect]
on the SEUS screen to restore the “connected” state. (In
case that the power does not turn on again, press the power
button.)
once and then on again. Accordingly, the SEUS goes in
“disconnect” state, but this is not a trouble. Click [Connect]
on the SEUS screen to restore the “connected” state. (In
case that the power does not turn on again, press the power
button.)
Fig. 6-1-44
2.
Initializing Single Page Data
By performing the following procedure, data of the page that you
want to initialize will be initialized.
want to initialize will be initialized.
Note 1:
If the 6D or 6E or 6F page data have been initialized, the
following adjustment needs to be performed again.
1) Camera system adjustments
following adjustment needs to be performed again.
1) Camera system adjustments
Note 2:
If the 8F page data have been initialized, the following
adjustment needs to be performed again.
1) LCD system adjustments
adjustment needs to be performed again.
1) LCD system adjustments
Initializing Method:
1) Select page: 00, address: 01 and set data: 01.
2) Click [Sector Write] on the SEUS screen to display the SEUS
1) Select page: 00, address: 01 and set data: 01.
2) Click [Sector Write] on the SEUS screen to display the SEUS
SECTOR WRITE screen.
3) Check that the SET ID is “0A”.
4) Click “All” of the option buttons of target page. (Fig. 6-1-44
4) Click “All” of the option buttons of target page. (Fig. 6-1-44
B
)
5) Click [Write] to write the initializing data to the flash memory
of the camera.
6) Wait for 3 sec.
7) Click [Close] to close the SEUS SECTOR WRITE screen.
8) Click [Save] on the SEUS screen.
9) Select page: 80, address: 34, and check that the data is “00”.
10) Select page: 80, address: 30, and check that the data is “00”.
11) When 4F page is initialized, perform “Initial Language Data
7) Click [Close] to close the SEUS SECTOR WRITE screen.
8) Click [Save] on the SEUS screen.
9) Select page: 80, address: 34, and check that the data is “00”.
10) Select page: 80, address: 30, and check that the data is “00”.
11) When 4F page is initialized, perform “Initial Language Data
Check”.
Processing after Completing Initializing
Order Page Address
Data
Procedure
1
40
28
01 [Set]
(Note)
Note:
At this time, the camera is reset and the power is turns off
once and then on again. Accordingly, the SEUS goes in
“disconnect” state, but this is not a trouble. Click [Connect]
on the SEUS screen to restore the “connected” state. (In
case that the power does not turn on again, press the power
button.)
once and then on again. Accordingly, the SEUS goes in
“disconnect” state, but this is not a trouble. Click [Connect]
on the SEUS screen to restore the “connected” state. (In
case that the power does not turn on again, press the power
button.)
B
A
0A
Click on the first or last page to see other DSC-S600 (serv.man4) service manuals if exist.