Read Sony DSC-RX1 (serv.man2) Service Manual online
DSC-RX1_L2
2-4
2-1-2. MAIN BOARD/LENS SECTION
ns : not supplied
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
51
A-1911-372-A
SERVICE, LSV-1600A (Note 2, 4)
52
A-1902-990-A SY-1001 BOARD, COMPLETE (SERVICE)
53
4-444-597-01
SHEET (C), SY RADIATION
54
Selection Parts SHIM (Note 3)
55
A-1912-509-A IM IMAGER UNIT
(including IC005 (CMOS imager) and CD-1001 board)
(Note 1, 2, 4)
56
1-856-431-11
FILTER BLOCK, OPTICAL
57
4-110-938-01 SHEET,
SPACER
58
1-886-676-11
CN-1010 FLEXIBLE BOARD
59
1-886-677-11
CN-1011 FLEXIBLE BOARD
60
4-443-544-01
TAPE, SHEET METAL FIXED
61
4-443-543-01 RADIATION
(SHEET
A)
62
4-448-993-01
SHEET (B), RADIATION
63
4-442-740-01
HEAT SINK (GOLD)
64
4-448-670-01 GASKET
(CD)
65
4-444-596-01
SHEET (B), SY RADIATION
66
4-442-739-02 FRAME,
SEAL
67
2-590-635-01
TAPE (AS 1/2)
68
4-451-782-01
SHEET (LE), RADIATION
#1
2-635-562-11 SCREW
(M1.7)
#113 2-635-562-41 SCREW
(M1.7)
#286
7-627-852-48
PRECISION SCREW +P1.7X3.5TYPE3
1. Remove in numerical order (
1
to
5
) in the left figure.
DISASSEMBLY
Note
1
#1 X 1
Back View
#1
Tightening torque =
0.12 0.01N m (1.2 0.1kg f cm)
0.12 0.01N m (1.2 0.1kg f cm)
SY
-
100
1
A
B
B
A
#113
#286
#1
#286
ns
ns
ns
51
(Note 2, 4)
52
1
58
4
5
59
63
2
55
(including IC005
(CMOS imager)
and CD1001 board)
(Note 1, 2, 4)
(CMOS imager)
and CD1001 board)
(Note 1, 2, 4)
When you re-assembly, clean up the surfaces
of LENS and OLPF using alcohol.
In addition, ensure that the receiver is not
covered with dusts.
of LENS and OLPF using alcohol.
In addition, ensure that the receiver is not
covered with dusts.
53
54
(Note 3)
54
(Note 3)
54
(Note 3)
57
60
66
65
62
61
64
56
67
68
68
3
BTH/JK Section
(See Page 2-5)
Note 1: Refer to “Assembly-8: Notes on Replacing the Optical Filter
Block.” when you assemble.
Note 1:
組立時は Assembly-8: Notes on Replacing the Optical Filter
Block.
を参照してください。
5
#286 X 3
Back View #286
6
#286 X 4
Back View #286
#286
7
#113 X 4
Back View
#113
#113
Screw
#1: M1.7 X 2.5
(Black)
2-635-562-11
2-635-562-11
2.5
1.7
#113: M1.7 X 5.0
(Black)
2-635-562-41
2-635-562-41
5.0
1.7
#286:
M1.7 X 3.5
3.5
1.7
(Black)
7-627-852-48
7-627-852-48
Note 2: The lens is paired with the Rear Tube.
Before replacing the lens, make sure that the lens and the
Rear Tube are in a pair according to “Assembly-1: Notes on
Assembling the IM Imager Unit and Lens Block”.
Rear Tube are in a pair according to “Assembly-1: Notes on
Assembling the IM Imager Unit and Lens Block”.
Note 2:
レンズと後部鏡筒は一対になっています。
レンズを交換する際は， Assembly-1： Notes on Assem-
bling the IM Imager Unit and Lens Block.
を参照し，対であ
ることを確認してください。
Note 3: The number or type of these parts needs to be selected ac-
cording to adjustment etc..
Select the part referring to “1-4. NOTES ON REPLACING
THE LSV-1600A DEVICE AND THE IM IMAGER UNIT”.
THE LSV-1600A DEVICE AND THE IM IMAGER UNIT”.
Note 3:
これらの部品は調整などによって使用個数や種類を選択する
必要があります。
1-4. LSV-1600A
デバイスおよびIMイメージャーユニット交
換時の注意 を参照して選択してください。
Note 4: NOTES ON REMOVING/INSTALLING THE IMAGER
BOARD
With the following features, this unit is likely to capture
foreign particles.
foreign particles.
・ The imager sensor size is large.
・ The space between the imager sensor and the lens
is small.
Therefore, pay close attention to foreign particles.
Note 4:
イメージャ基板の取り外し／取り付け時の注意
本機は下記のような特徴があるため、ゴミが写り
こみやすい傾向があります。
こみやすい傾向があります。
・ イメージセンサーのサイズが大きい
・ イメージセンサーとレンズの間隔がせまい
そのため、ゴミに対しては細心の注意を払ってく
ださい。
ださい。
Click on the first or last page to see other DSC-RX1 (serv.man2) service manuals if exist.