Read Sony DSC-L1 (serv.man13) Service Manual online
MANUAL DE SERVIÇO
LEVEL
2
Link
NOTA DE SERVIÇO
DESMONTAGEM
DIAGRAMAS EM BLOCOS
DIAGRAMAS DAS PLACAS
DIAGRAMAS ESQUEMÁTICO
PLACAS DE CIRCUITO IMPRESSO
LISTA DE PEÇAS PARA REPARO
ESPECIFICAÇÕES
Link
Alteração do código
Instruções do
Acrobat Reader
•
Para AJUSTES
(SECTION 6),
consulte o
MANUAL DE SERVIÇO
, ADJ (9-
890-117
-51).
• Reference No. search on printed wiring boards is available.
• The Cautions at the Time of Lens Block Handling
• The Method of Attachment of LC-084 Flexible Board
• The Method of Attachment of USB and DC IN Jacks on the JK-276 Flexible Board
• HELP: Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
• The Method of Attachment of LC-084 Flexible Board
• The Method of Attachment of USB and DC IN Jacks on the JK-276 Flexible Board
• HELP: Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
Ver 1.2 03.2005
CÂMERA DIGITAL
On the CH-147 and SY-110 boards
This service manual procides the information that is premised the
circuit board replacement service and not intended repair inside the
CH-147 and SY-110 boards.
Therefore, schematic diagram, printed wiring board and electrical
parts list of the CH-147 and SY-110 boards are not shown.
The following pages are not shown.
circuit board replacement service and not intended repair inside the
CH-147 and SY-110 boards.
Therefore, schematic diagram, printed wiring board and electrical
parts list of the CH-147 and SY-110 boards are not shown.
The following pages are not shown.
Schematic diagram ................... Pages 4-9 to 4-28
Printed wiring board .................. Pages 4-37 to 4-40
Waveforms ................................ Pages 4-49 and 4-50
Mounted parts location .............. Page 4-51
Electrical parts list ..................... Pages 5-7 and 5-10 to 5-13
Printed wiring board .................. Pages 4-37 to 4-40
Waveforms ................................ Pages 4-49 and 4-50
Mounted parts location .............. Page 4-51
Electrical parts list ..................... Pages 5-7 and 5-10 to 5-13
The above-described information is shown in service manual Level 3.
DSC-L1
Brazilian Model
Foto: Silver
DSC-L1
9-890-117-31
Sony EMCS Co.
Published by DI Technical Support Section - Traduzido Sony Brasil Ltada - Engenharia da Qualidade
©2004.10
2004I0500-1
— 2 —
DSC-L1
ý
)MAGE
4OTAL
!PPROX
%FFECTIVE
!PPROX
,ENS
#ARL
%XPOSURE
!UTOMATIC
7HITE
!UTOMATIC
&ILE
3TILL
2ECORDING
h-EMORY
&LASH
2ECOMMENDED
ESPECIFICAÇÕES
;)NPUT
53"
(I
3PEED
;,#$
,#$
4OTAL
;0OWER
5SED
.0
&4
0OWER
0OWER
/PERATING
#
3TORAGE
n #
$IMENSIONS
!PPROX
-ASS
!PPROX
-ICROPHONE
%LECTRET
3PEAKER
#OMPATIBLE
0ICT"RIDGE
#OMPATIBLE
ý
)NPUT
/UTPUT
/PERATING
#
3TORAGE
n #
$IMENSIONS
!PPROX
-ASS
!PPROX
ý
5SED
,ITHIUM
ION
-AXIMUM
$#
.OMINAL
$#
#APACITY
ý
s
$ESIGN
See page 5-14.
— 3 —
DSC-L1
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE WITH
MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE
0
SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
1.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
connections. Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
of deterioration. Point them out to the customer and
recommend their replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40
• Unleaded solder melts at a temperature about 40
°
C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°
C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Replace only with the same or equivalent type.
— 4 —
DSC-L1
ÍNDICE
1.
NOTA DE SERVIÇO
1-1.
Note for Repair ································································ 1-1
1-2.
Discharging of the ST-109 Flexible Board’s Charging
Capacitor (C050) ····························································· 1-1
Capacitor (C050) ····························································· 1-1
1-3.
The Cautions at the Time of Lens Block Handling ········· 1-2
1-4.
Description on Self-diagnosis Display ···························· 1-2
2.
DESMONTAGEM
2-1.
Disassembly ····································································· 2-1
2-2.
Service Position ······························································· 2-5
2-3.
The Method of Attachment of LC-084 Flexible Board ··· 2-7
2-4.
The Method of Attachment of USB and DC IN Jacks
on the JK-276 Flexible Board ········································· 2-9
on the JK-276 Flexible Board ········································· 2-9
2-5.
Circuit Boards Location ················································ 2-10
3.
DIAGRAMAS EM BLOCOS
3-1.
Overall Block Diagram (1/2) ··········································· 3-1
3-2.
Overall Block Diagram (2/2) ··········································· 3-3
3-3.
Power Block Diagram (1/2) ············································· 3-5
3-4.
Power Block Diagram (2/2) ············································· 3-7
4.
PLACAS DE CIRCUITO IMPRESSO E
DIAGRAMAS ESQUEMÁTICOS
DIAGRAMAS ESQUEMÁTICOS
4-1.
Frame Schematic Diagram ·············································· 4-1
4-2.
Schematic Diagrams ························································ 4-5
CD-526 FLEXIBLE (CCD IMAGER) ··························· 4-7
JK-276 FLEXIBLE (JACK, CONTROL SWITCH) ···· 4-29
ST-109 FLEXIBLE (FLASH DRIVE) ························· 4-31
SW-432 FLEXIBLE (CONTROL SWITCH) ··············· 4-33
MS-238 FLEXIBLE
(MEMORY STICK CONNECTOR) ···························· 4-34
LC-084 FLEXIBLE (LENS COVER MOTOR) ··········· 4-34
JK-276 FLEXIBLE (JACK, CONTROL SWITCH) ···· 4-29
ST-109 FLEXIBLE (FLASH DRIVE) ························· 4-31
SW-432 FLEXIBLE (CONTROL SWITCH) ··············· 4-33
MS-238 FLEXIBLE
(MEMORY STICK CONNECTOR) ···························· 4-34
LC-084 FLEXIBLE (LENS COVER MOTOR) ··········· 4-34
4-3.
Printed Wiring Boards ··················································· 4-35
JK-276 FLEXIBLE ······················································· 4-41
ST-109 FLEXIBLE ······················································· 4-43
SW-432 FLEXIBLE ······················································ 4-45
MS-238 FLEXIBLE ······················································ 4-47
LC-084 FLEXIBLE ······················································· 4-47
JK-276 FLEXIBLE ······················································· 4-41
ST-109 FLEXIBLE ······················································· 4-43
SW-432 FLEXIBLE ······················································ 4-45
MS-238 FLEXIBLE ······················································ 4-47
LC-084 FLEXIBLE ······················································· 4-47
4-5.
Mounted Parts Location ················································ 4-52
5.
LISTA DE PEÇAS PARA REPARO
5-1.
Exploded Views ······························································· 5-2
5-1-1. Cabinet (Front) Block ······················································ 5-2
5-1-2. Cabinet (Upper) Block ···················································· 5-3
5-1-3. Battery Holder Block ······················································· 5-4
5-1-4. Cabinet (Rear) Block ······················································· 5-5
5-2.
5-1-2. Cabinet (Upper) Block ···················································· 5-3
5-1-3. Battery Holder Block ······················································· 5-4
5-1-4. Cabinet (Rear) Block ······················································· 5-5
5-2.
Electrical Parts List ························································· 5-6
Section
Title
Page
