Read Sony DSC-J10 Service Manual online
DSC-J10
Sony Corporation
SERVICE MANUAL
Revision History
SERVICE NOTE (Check the following note before the service.)
983454411.pdf
2010L29-1
© 2010.12
Published by Sony Techno Create Corporation
Ver. 1.0 2010.12
DIGITAL STILL CAMERA
9-834-544-11
US Model
AEP Model
UK Model
E Model
Chinese Model
Hong Kong Model
Korea Model
Argentine Model
Tourist Model
DSC-J10
Ver.
Date
History
Contents
S.M. Rev.
issued
1.0
2010.12
Official Release
—
—
1-1. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
1-2. PRECAUTION ON REPLACING THE LENS
1-3. REGARDING FUSE
Photo: Blue
Internal memory
ON BOARD
Internal memory
ON BOARD
The components identified
by mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number
specified.
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
DSC-J10
– 2 –
SPECIFICATIONS
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY
SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes and
bridges.
2. Check the interboard wiring to ensure that no wires are “pinched”
or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs of
deterioration. Point them out to the customer and recommend their
replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 350°C during
repairing.
• Do not touch the soldering iron on the same conductor of the circuit
board (within 3 times).
• Be careful not to apply force on the conductor when soldering or
unsoldering.
UNLEADED SOLDER
This unit uses unleaded solder.
Boards requiring use of unleaded solder are printed with the lead free
mark (LF) indicating the solder contains no lead.
(
Caution: Some printed circuit boards may not come printed with the
lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
• Set the soldering iron tip temperature to 350°C approximately.
If cannot control temperature, solder/unsolder at high temperature
for a short time.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
Unleaded solder is more viscous (sticky, less prone to
flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
• Be sure to control soldering iron tips used for unleaded solder and
those for leaded solder so they are managed separately. Mixing un-
leaded solder and leaded solder will cause detachment phenomenon.
Camera
[System]
[System]
Image device: 7.75 mm (1/2.3 type)
color CCD, Primary color filter
Total pixel number of camera:
Approx. 16.4 Megapixels
Effective pixel number of camera:
Approx. 16.1 Megapixels
Lens: 4 × zoom lens
F3.5 (W) - F4.6 (T)
f = 6.18 mm - 24.7 mm (35 mm -
140 mm (35 mm film equivalent))
Scene Selection (10 modes)
White balance: Automatic, Daylight,
Cloudy, Fluorescent 1/2/3,
Incandescent, Flash, One Push
Recording interval for Burst mode:
Approx. 0.95 second
File format:
Still images: JPEG (DCF Ver. 2.0,
Exif Ver. 2.3, MPF Baseline)
compliant
Movies: AVI (Motion JPEG)
Recording media: Internal Memory
(Approx. 4 GB)
1 GB equals 1 billion bytes, a
When measuring media capacity,
portion of which is used for system
files.
Available user capacity: Approx.
3.9 GB
Flash: Flash range (ISO sensitivity
(Recommended Exposure Index)
set to Auto):
Approx. 0.2 m to 3.6 m (W)
(7 7/8 inches to 11 feet 9 3/4 inches)
Approx. 0.2 m to 2.8 m (T)
(7 7/8 inches to 9 feet 2 1/4 inches)
[Input and Output connectors]
USB arm: type A (built-in)
USB communication: Hi-Speed USB
(USB 2.0)
Exposure control: Automatic exposure,
[LCD screen]
LCD panel: 6.7 cm (2.7 type) TFT drive
Total number of dots: 230,400 (960 ×
240) dots
[Power, general]
Power:
(wall socket) by connecting with
Built-in rechargeable battery
pack: 3.7 V
Supplied from the wall outlet
Power consumption (during
the supplied AC adaptor (AC-
UB10): 5 V
shooting): 1.6 W
Operating temperature: 0
°
C to 40
°
C
Storage temperature: -20
°
C to -60
°
C
(-4
°
F to +140
°
F)
(32
°
F to 104
°
F)
Dimensions:
93.6 × 59.4 × 17.3 mm
(3 3/4 × 2 3/8 × 1 1/16 inches)
(W/H/D, excluding protrusions)
Mass:
Approx. 126 g (4.4 oz.)
Microphone: Monaural
Speaker: Monaural
Exif Print: Compatible
management and/or application
•
•
•
•
PRINT Image Matching III:
Compatible
AC adaptor (AC-UB10)
Power requirements: AC 100 V to
240 V, 50 Hz/60 Hz, 70 mA
Output voltage: DC 5 V, 0.5 A
Operating temperature: 0
°
C to 40
°
C
(32
°
F to 104
°
F)
Storage temperature: -20
°
C to +60
°
C
(-4
°
F to +140
°
F)
Dimensions: Approx. 50 × 22 × 54 mm
(2 × 7/8 × 2 1/4 inches) (W/H/D)
Mass: Approx. 48 g (1.7 oz) (For USA
and Canada models), Approx. 43 g
(1.5 oz) (Except USA and Canada
models)
Design and specifications are subject to
change without notice.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES
SUPPLÉMENTS PUBLIÉS PAR SONY.
Caution
Danger of explosion occurs if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
DSC-J10
1-1E
1. SERVICE NOTE
1-1.
METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.)
Note1: When replacing the Main Board Assy, erase the data in internal memory of main board before replacement.
Note2: When replacing the Main Board Assy, execute formatting and initialize the internal memory after replacement.
Method for Copying the Data in Internal Memory
1-2.
PRECAUTION ON REPLACING THE LENS
When replacing the lens, write down the Tele Limit Data given on the data sheet of the replacement lens for service.
Execute the J10 Write Zoom Calib Value.
For details of adjusting method, please refer to the Service manual ADJ of DSC-J10 (9-834-544-5[]).
Method for Formatting the Internal Memory
Note: The Tele Limit Data of lens is written only repair parts.
Importing images to a computer (Windows)
“PMB” allows you to easily import images.
For details on “PMB” functions, see the “PMB Help”.
Importing images to a computer without using “PMB”
When the AutoPlay Wizard appears after making a USB connection between the camera
When the AutoPlay Wizard appears after making a USB connection between the camera
and a computer, click [Open folder to view files]
[OK]
[DCIM]
copy the desired
images to the computer.
Format
Formats the internal memory. Note that formatting permanently erases all data on the
internal memory, and is unrecoverable. Save precious data on a computer, etc.
(Settings)
(Internal Memory Tool)
[Format]
[OK]
Note
Note that formatting permanently erases all data including even protected images.
1. MENU
XXX
X
Tele Limit Data
XXXX
1-3. REGARDING FUSE
• MAIN BOARD
Ref. No:
F2
Part No:
1-576-415-11
Description: FUSE, MICRO (1608 TYPE) (2A/32V)
F2
F1
Ref. No:
F1
Part No:
1-576-415-11
Description: FUSE, MICRO (1608 TYPE) (2A/32V)
DSC-J10
2-1
Link
2. REPAIR PARTS LIST
Follow the disassembly in the numerical order given.
IDENTIFYING PARTS
View Position
(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from the original one.
• Items marked “*” are not stocked since they are seldom required for routine service. Some
delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Due to standardization, replacements in the parts list may be different from the parts speci-
fied in the diagrams or the components used on the set.
• Abbreviation
AR : Argentine model
CH : Chinese model
HK : Hong Kong model
KR : Korea model
TW : Taiwan model
JE
: Tourist model
Back View
Bottom View
Right View
Front View
Left View
Top View
ACCESSORIES
ASSEMBLY
DISCHARGING OF THE CHARGING CAPACITOR
• Color Indication of Appearance Parts
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
Les composants identifiés par une marque
0
sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
When indicating parts by reference
number, please include the board name.
2
Front Cover Assy
1
Rear Cover Assy
qa
Main Board Assy
7
USB Holder
5
SW Board
8
LCD Bracket Assy
qs
Chassis
6
LCD Module
0
ST Board
9
Optical Unit
3
Battery