Read Sony DSC-H5 (serv.man2) Service Manual online
DSC-H5_L2
4-3
4-2. SCHEMATIC DIAGRAMS
4-2. SCHEMATIC DIAGRAMS
Link
(For schematic diagrams)
• All capacitors are in
• All capacitors are in
µ
F unless otherwise noted. pF :
µ
µ
F. 50 V or less are not indicated except for electrolytics
and tantalums.
• Chip resistors are 1/10 W unless otherwise noted.
k
Ω
=1000
Ω
, M
Ω
=1000 k
Ω
.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum
capacitor, Because it is damaged by the heat.
Be careful not to heat the minus side of tantalum
capacitor, Because it is damaged by the heat.
• Some chip part will be indicated as follows.
Example
C541
L452
22U
10UH
TA A
2520
• Constants of resistors, capacitors, ICs and etc with XX
indicate that they are not used.
In such cases, the unused circuits may be indicated.
In such cases, the unused circuits may be indicated.
• Parts with * differ according to the model/destination.
Refer to the mount table for each function.
• All variable and adjustable resistors have characteristic
curve B, unless otherwise noted.
• Signal name
XEDIT
→
EDIT
PB/XREC
→
PB/REC
• 2: non flammable resistor
• 5: fusible resistor
• C: panel designation
•
• 5: fusible resistor
• C: panel designation
•
A
: B+ Line
•
B
: B– Line
•
J
: IN/OUT direction of (+,–) B LINE.
•
C
: adjustment for repair.
(Measuring conditions voltage)
• Voltages are measured between the measurement
points and ground when camera shoots color bar chart
of pattern box. They are reference values.
(VOM of DC 10 M
of pattern box. They are reference values.
(VOM of DC 10 M
Ω
input impedance is used)
• Voltage values change depending upon input
impedance of VOM used.)
Precautions for Replacement of imager
• If the imager has been replaced, carry out all the
adjustments for the camera section.
• As the imager may be damaged by static electricity from
its structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with
dusts nor exposed to strong light.
In addition, ensure that the receiver is not covered with
dusts nor exposed to strong light.
1. Connection
2. Adjust the distance so that the output waveform of
Fig. a and the Fig. b can be obtain.
When indicating parts by reference number, please
include the board name.
include the board name.
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS
(In addition to this, the necessary note is printed in each block)
(In addition to this, the necessary note is printed in each block)
Kinds of capacitor
Temperature characteristics
External dimensions (mm)
Y
ello
w
A
A
B
B
A=B
Fig. a (Video output terminal output waveform)
Electronic beam
scanning frame
scanning frame
CRT picture frame
H
Cy
an
Green
White
Magenta
Red
Blue
Fig.b (Picture on monitor TV)
Note :
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Note :
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
Pattern box
Front of the lens
L = 1 m (PTB-450)
L = 40 cm (PTB-1450)
L = 40 cm (PTB-1450)
L
Camera
Pattern box PTB-450
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
For PTB-450:
J-6020-250-A
J-6020-250-A
For PTB-1450:
J-6082-559-A
J-6082-559-A
Pattern box
Color bar chart
4-2. SCHEMATIC DIAGRAMS
Click on the first or last page to see other DSC-H5 (serv.man2) service manuals if exist.