Read Sony DSC-F717 (serv.man6) Service Manual online
SERVICE MANUAL
DSC-F717_ADJ
ADJ
Ver 1.1 2007.02
Sony EMCS Co.
9-929-994-82
2007B0500-1
© 2007.2
Published by Kohda TEC
SUPPLEMENT-1
File this supplement with the service manual.
(DI06-164)
• Change of Service Tool Supply
• Adjustment and Checking after CCD Block Assy
• Adjustment and Checking after CCD Block Assy
Replacement
DSC-F717
Change of Service Tool Supply
Formerly the CPC-12 jig was supplied with the extension cable inserted in the CPC-12 board, but this time the board and the cable are
separated and supplied individually. Only the necessary part can be purchased.
separated and supplied individually. Only the necessary part can be purchased.
Former
New
CPC-12 jig
J-6082-436-A
J-6082-436-A
CPC-12 board
J-6082-436-1
J-6082-436-1
Extension cable
(22P)
J-6082-436-2
(22P)
J-6082-436-2
— 2 —
DSC-F717_ADJ
Adjustment and Checking after CCD Block Assy Replacement
After the CCD Block Assy was replaced, adjust the same items as the adjusting items to be performed when the Lens Block Assy was
replaced.
replaced.
[Reference: Adjusting items when replacing Lens Block Assy]
• Hall adj.
• Flange back adj.
• F No. compensation
• Mechanical shutter adj.
• Light value adj.
• Mixed color cancel adj.
• Auto white balance standard data input
• Color reproduction adj.
• CCD (white and black) defect compensation
• CCD linearity check
• Strobe white balance adj.
• Hall adj.
• Flange back adj.
• F No. compensation
• Mechanical shutter adj.
• Light value adj.
• Mixed color cancel adj.
• Auto white balance standard data input
• Color reproduction adj.
• CCD (white and black) defect compensation
• CCD linearity check
• Strobe white balance adj.
After the adjustments finished, check the image quality using the specified chart. (Refer to “Image Quality Check”)
If it’s determined as picture defects like partial de-focusing, replace the Lens Block Assy since lens barrel might be damaged.
If it’s determined as picture defects like partial de-focusing, replace the Lens Block Assy since lens barrel might be damaged.
— 3 —
DSC-F717_ADJ
Image Quality Check
For the chart and limited sample used for image quality check, please contact the service headquarter of each area.
Chart Specification
Letter Height
10 mm
Font
MS P Gothic
Letter Pitch
horizontal 16 mm
vertical 12.5 mm
Total horizontal length of chart
1180 mm
Total vertical length of chart
840 mm
Letter Pitch
Preparing the chart
Setting position of the chart and camera
12.5 mm
16 mm
1180 mm
A4 Sheet
Tape together 16 sheets (A4 size)
840 mm
Chart
(Set vertically)
Approximately 6.1 m
Use a tripod
Adjust the center line of the chart and camera
DSC-F717
— 4 —
DSC-F717_ADJ
How to check picture blur after replacing CCD Block Assy
1)
Turn on the power.
2) Change the mode dial to “A” (Aperture mode).
3)
3)
Set “DIGITAL ZOOM” to “OFF” in the SET UP settings.
4)
Set the zoom to TELE end.
5)
Open the aperture of lens, and set aperture value to “F2.4”.
6)
Set “IMAGE SIZE” to “2560
×
1920” (5M).
7)
Record the still image with self-timer to avoid blurring of image.
8)
Compare on a personal computer the lower left of limited sample with the picture periphery shot with the repaired camera.
Note:
Compare with maximum image size.
Judging standard
Images are blur more than “Limited Sample”.
NG
Images are same or blur less than “Limited Sample”.
OK
If it's determined as picture defects like partial de-focusing, replace the Lens Block Assy since lens barrel might be damaged.
Limited sample
Recorded still image
Compare on a personal computer
the lower left of limited sample with
the picture periphery shot with the
repaired camera.
