Read Sony DSC-F505 (serv.man5) Service Manual online
DSC-F505
Ver 1.1 1999.10
4-1
SECTION 4
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
(For printed wiring boards)
•
•
b
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
• Through hole is omitted.
• Circled numbers refer to waveforms.
• There are few cases that the part printed on diagram
• Circled numbers refer to waveforms.
• There are few cases that the part printed on diagram
isn’t mounted in this model.
• Chip parts.
(For schematic diagrams)
• All capacitors are in
• All capacitors are in
µ
F unless otherwise noted. pF :
µµ
F.
50V or less are not indicated except for electrolytics and
tantalums.
tantalums.
• Chip resistors are 1/10W unless otherwise noted.
k
Ω
=1000
Ω
, M
Ω
=1000k
Ω
.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum capacitor, Be-
Be careful not to heat the minus side of tantalum capacitor, Be-
cause it is damaged by the heat.
• Some chip part will be indicated as follows.
Example
C541
L452
22U
10UH
TA A
2520
• Constants of resistors, capacitors, ICs and etc with XX indicate
that they are not used.
In such cases, the unused circuits may be indicated.
• Parts with
★
differ according to the model/destination.
Refer to the mount table for each function.
• All variable and adjustable resistors have characteristic curve B,
unless otherwise noted.
• Signal name
XEDIT
→
EDIT PB/XREC
→
PB/REC
•
2
: non flammable resistor
•
1
: fusible resistor
•
C
: panel designation
•
A
: B+ Line
*
•
B
: B– Line
*
•
J
: IN/OUT direction of (+,–) B LINE.
*
•
C
: adjustment for repair.
*
• Circled numbers refer to waveforms.
*
*
Indicated by the color red.
(Measuring conditions voltage and waveform)
• Voltages and waveforms are measured between the measure-
ment points and ground when camera shoots color bar chart of
pattern box. They are reference values and reference wave-
forms.
pattern box. They are reference values and reference wave-
forms.
(VOM of DC 10 M
Ω
input impedance is used.).
• Voltage values change depending upon input impedance of VOM
used.)
1. Connection
2. Adjust the distance so that the output waveform of Fig. a and
the Fig. b can be obtain.
THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS
(In addition to this, the necessary note is printed in each block)
(In addition to this, the necessary note is printed in each block)
Transistor
Diode
Kinds of capacitor
Temperature characteristics
External dimensions (mm)
Note :
The components identified by
mark
The components identified by
mark
!
or dotted line with mark
!
are critical for safety.
Replace only with part number
specified.
specified.
Note :
Les composants identifiés par
une marque
Les composants identifiés par
une marque
!
sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
Ne les remplacer que par une
pièce portant le numéro spécifié.
When indicating parts by reference number, pleas include
the board name.
the board name.
Front of the lens
About 90 cm
Pattern box
Y
e
llo
w
A
A
B
B
A=B
Fig. a (Video output terminal output waveform)
H
Cy
an
Green
White
Magenta
Red
Blue
Fig.b (Picture on monitor TV)
Electron beam
scanned frame
scanned frame
CRT picture frame
Y
ello
w
Cy
an
Green
White
Magenta
Red
Blue
C
B
E
5
6
4
2
1
3
5
4
6
2
3
1
4
5
2
3
1
1
2
4
5
3
3
2
1
3
2
1
3
2
1
4
3
1
2
Click on the first or last page to see other DSC-F505 (serv.man5) service manuals if exist.