XVM-B62 - Sony Car Audio Service Manual (repair manual)

xvm-b62 service manual
Model
XVM-B62
Pages
36
Size
1.97 MB
Type
PDF
Document
Service Manual
Brand
Device
Car Audio
File
xvm-b62.pdf
Date

Read Sony XVM-B62 Service Manual online

SERVICE MANUAL
Sony Corporation
eVehicle Division
Published by Sony Techno Create Corporation
US Model
Canadian Model
E Model
Chinese Model
MOBILE MONITOR
9-887-112-02
2007E04-1
© 2007.05
Ver. 1.1  2007.05
SPECIFICATIONS
XVM-B62
Monitor
System
Liquid crystal color display
Drive system
TFT-LCD active matrix system
Picture size
6.2 inches wide screen (16:9)
137.5 
× 77.2 mm
(5
 1/2
 
× 3
 1/8
 in.) (w 
× h)
Picture segment
336,960 (w 1440 
× h 234) dots
Power requirements
12 V DC car battery (negative ground)
Current drain
Approx. 550 mA
Dimensions
164.2 
× 106.6 × 29 mm
(6
 1/2
 
× 4
 1/4
 
× 1
 1/16
 in.) (w/h/d)
Operating temperature
°C – 45 °C (32 °F – 113 °F)
Mass
Approx. 450 g (1 lb)
Supplied accessories
Power supply cord (1)
Video in cable (3 m) (1)
Tap (1)
Collar (1)
Operating Instructions (1)
Monitor stand (1)
(with suppled screws (5))
(E model)
Design and specifications are subject to change
without notice.
2
XVM-B62
TABLE OF CONTENTS
1.
SERVICING NOTES
................................................
3
2.
GENERAL
Location of Controls ........................................................
4
Connections .....................................................................
5
3.
DISASSEMBLY
3-1.
Case (Front) Section ........................................................
7
3-2.
Main Board, LCD Unit ....................................................
7
4.
TEST MODE
...............................................................
8
5.
ELECTRICAL ADJUSTMENTS
5-1.
Equipment Used ..............................................................
9
5-2.
Connection of Equipment ................................................
9
5-3.
Setup for Adjustment .......................................................
9
5-4.
DC-DC Converter Adjustment ........................................ 10
     5-4-1.   Frequency Adjustment ............................................. 10
     5-4-2.   5V Voltage Adjustment ............................................ 10
     5-4-3.   Other Voltage Checks ............................................... 10
5-5.
PLL Adjustment .............................................................. 10
     5-5-1.   Frequency Adjustment ............................................. 10
5-6.
Inverter High Voltage Check ........................................... 10
     5-6-1.   Voltage Check .......................................................... 10
     5-6-2.   Frequency Check ..................................................... 10
5-7.
OSD Dot Clock Check .................................................... 10
5-8.
NTSC Subcarrier Check .................................................. 11
5-9.
PAL Subcarrier Check ..................................................... 11
5-10. V COM Voltage/Position Adjustment ............................. 11
5-11. Video Adjustment ............................................................ 11
     5-11-1.   Brightness Signal Contrast Level (Y GAIN) ......... 11
     5-11-2.   Black Limiter Level Adjustment ............................ 11
     5-11-3.   White Limiter Level Adjustment ........................... 11
     5-11-4.   Rch Sub Bright Adjustment ................................... 12
     5-11-5.   Bch Sub Bright Adjustment ................................... 12
     5-11-6.   Rch Sub Contrast Adjustment ................................ 12
     5-11-7.   Bch Sub Contrast Adjustment ................................ 12
     5-11-8.   
γ 1 Adjustment ....................................................... 12
     5-11-9.   
γ 2 Adjustment ....................................................... 12
     5-11-10. VCO Free Run Adjustment .................................... 13
     5-11-11. V Pos Adjustment .................................................. 13
     5-11-12. H Pos Adjustment .................................................. 13
5-12. Flicker and White Balance Adjustment ........................... 13
     5-12-1.   Flicker Adjustment ................................................. 13
     5-12-2.   White Balance Adjustment .................................... 13
6.
DIAGRAMS
6-1.
Block Diagram –Video Section– ..................................... 15
6-2.
Block Diagram –Display Section– .................................. 16
6-3.
Printed Wiring Board –Main Section– ............................ 18
6-4.
Schematic Diagram –Main Section (1/2)– ...................... 20
6-5.
Schematic Diagram –Main Section (2/2)– ...................... 21
6-6.
Printed Wiring Board –Connector Section– .................... 22
6-7.
Schematic Diagram –Connector Section– ....................... 22
7.
EXPLODED VIEWS
7-1.
Rear Section .................................................................... 29
7-2.
Front Section ................................................................... 30
8.
ELECTRICAL PARTS LIST
.................................. 31
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
 : LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40
°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
Notes on Chip Component Replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged
by heat.
SAFETY-RELATED  COMPONENT  WARNING!!
COMPONENTS  IDENTIFIED  BY  MARK  0  OR  DOTTED  LINE
WITH  MARK  
0  ON  THE  SCHEMATIC  DIAGRAMS  AND  IN
THE  PARTS  LIST  ARE  CRITICAL  TO  SAFE  OPERATION.
REPLACE  THESE  COMPONENTS  WITH  SONY  PARTS  WHOSE
PART  NUMBERS  APPEAR  AS  SHOWN  IN  THIS  MANUAL  OR
IN  SUPPLEMENTS  PUBLISHED  BY  SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
 À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE  DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
3
XVM-B62
SECTION 1
SERVICE NOTES
NOTE FOR REPLACEMENT OF THE EEP ROM (IC403)
The EEP ROM (IC403) contains all data by which the LCD screen is defined.
When the EEP ROM is replaced, the normal LCD screen will not appear.
It is then necessary to write the data into the EEP ROM.
Writing Method:
1. Turn off power.
2. While holding the TEST switch (S408) down for more than 5 seconds, turn on power.
Then, release the TEST switch (S408).
3. Press the [DIMMER/--] button for more than 2 seconds.
4. The EEP ROM data will be written and the normal test mode screen will appear.
After this, perform V COM voltage/position adjustment as well as VIDEO adjustment.
NOTE FOR REPLACEMENT OF THE SYSTEM CONTROL (IC401)
When the IC401 is replaced, the video system should be set again according to the destinations.
Setting Method:
1. Enter the test mode. (See page 8).
2. Select NTSC/PAL SELECT from the test mode menu.
3. Set the video system to the appropriate mode for each destination by using the [INPUT/+] and [DIMMER/--] buttons.
Video mode
Destination
NTSC
US, Canadian
PAL
E, Chinese
Ver. 1.1
4
XVM-B62
SECTION 2
GENERAL
This section is extracted
from instruction manual.
6
Location of controls
INPUT/
 button
Press to select the desired input
source, VIDEO 1 or VIDEO 2.
DIMMER/
 button
Press to select the dimmer On/Off.
MENU button
POWER button
Monitor
1 2
3 4
Page of 36
Display

Download Sony XVM-B62 Service Manual (Repair Manual)

Here you can read online and download Sony XVM-B62 Service Manual in PDF. XVM-B62 service manual will guide through the process and help you recover, restore, fix, disassemble and repair Sony XVM-B62 Car Audio. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.