Read Sony XTL-6100MK2 Service Manual online
10
2.5 Vp-p
0 V
38.9 MHz
T1= 40.9 MHz
T2= 31.9 MHz
T2= 31.9 MHz
0.7 V
0.3 V
0.3 V
red
white (approx. 100%)
horizontal sync. signal
burst signal (flat)
TV SG
set
POWER (CN4)
RF out
ANT IN
DC
power supply
power supply
TRAP Adjustment
Procedure:
1. With the Power off, input the output of TG to TP30 (with DC
1. With the Power off, input the output of TG to TP30 (with DC
cut by a capacitor (0.01 µF)).
2. Connect a spectrum analyzer to TP31 (with DC cut by a
capacitor (0.01 µF)).
3. Adjust T1 so that the waveform peak is 40.9 MHz ± 50 Hz.
4. Adjust T2 so that the waveform peak is 31.9 MHz ± 50 Hz.
5. After this adjustment, open TP30 and TP31. (Disconnect the
4. Adjust T2 so that the waveform peak is 31.9 MHz ± 50 Hz.
5. After this adjustment, open TP30 and TP31. (Disconnect the
spectrum analyzer.)
VCO Adjustment
Procedure:
1. No connection to ANT IN. (no signal state)
2. Connect a resistor (10 k
1. No connection to ANT IN. (no signal state)
2. Connect a resistor (10 k
Ω
) between TP33 and +9 V (TP35).
3. Connect a spectrum analyzer to TP34 (with DC cut by a
capacitor (0.01 µF)).
4. Adjust T3 so that the waveform peak is 38.9 MHz ± 1 kHz.
5. After this adjustment, open TP34. (Disconnect the spectrum
5. After this adjustment, open TP34. (Disconnect the spectrum
analyzer.)
AGC Adjustment
Procedure:
1. Set the TV SYSTEM switch to 1.
2. Input a color bar signal of E8ch (196.25 MHz) and 66 dBµV
1. Set the TV SYSTEM switch to 1.
2. Input a color bar signal of E8ch (196.25 MHz) and 66 dBµV
(75
Ω
OPEN).
3. Connect the digital voltmeter to TP42.
4. Adjust VR1 so that reading on the digital voltmeter is
4. Adjust VR1 so that reading on the digital voltmeter is
6.0 ± 0.1 V.
AFT Adjustment
Procedure:
1. Input a color bar signal of E8ch (196.25 MHz) and 74 dBµV
1. Input a color bar signal of E8ch (196.25 MHz) and 74 dBµV
(75
Ω
OPEN).
2. Connect the oscilloscope to TP102.
3. Adjust T3 untill the waveform on the oscilloscope is 2.5 Vp-p.
3. Adjust T3 untill the waveform on the oscilloscope is 2.5 Vp-p.
• Use the following equipment for the electrical adjustment.
Equipment
1 Monitor TV (XVM-6100MK2, etc.)
2 Spectrum analyzer
3 TV signal generator
4 Digital voltmeter
5 Oscilloscope
6 Audio analyzer
7 DC power supply
8 Frequency counter
2 Spectrum analyzer
3 TV signal generator
4 Digital voltmeter
5 Oscilloscope
6 Audio analyzer
7 DC power supply
8 Frequency counter
Equipment Connections
Connect the test equipment as shown in the figure below (unless
otherwise instructed) and perform the adjustment.
otherwise instructed) and perform the adjustment.
Setup during Adjustment
Use the video signal obtained from the TV signal generator as the
alignment signal, and check that this signal is within video output
signal standards.
alignment signal, and check that this signal is within video output
signal standards.
Connection points: Refer to page 12.
Adjustment points: Refer to page 12.
Adjustment points: Refer to page 12.
TUNER UNIT SECTION
Color bar signal from TV signal generator
Note:
Small peaks (dips) coming out from the top of the
waveform are unacceptable.
waveform are unacceptable.
Click on the first or last page to see other XTL-6100MK2 service manuals if exist.