Read Sony XR-CA600X / XR-CA620X Service Manual online
XR-CA600X/CA620X
24
24
6-10.
IC PIN FUNCTION DESCRIPTION
Pin No.
Pin Name
I/O
Description
44
BUSCKO
O
Serial data transfer clock signal output to the SONY bus interface (IC581)
45
IIC SIO
I/O
Two-way data IIC bus with the FM/AM tuner unit (TU1), and electrical volume (IC331)
46
NCO
O
Not used (open)
47
IIC CKO
O
IIC bus clock signal output to the FM/AM tuner unit (TU1), and electrical volume (IC331)
48
AMPON
O
Standby on/off control signal output to the power amplifier (IC751)
“L”: standby mode, “H”: amplifier on
“L”: standby mode, “H”: amplifier on
49
AMPATT
O
Muting on/off control signal output to the power amplifier (IC751) “L”: muting on
50
ATT
O
Audio line muting on/off control signal output “H”: muting on
51
NCO
O
Not used (open)
52
AMSON
O
Tape auto music sensor control signal output to the CXA2509AQ (IC301)
“L”: auto music sensor on
“L”: auto music sensor on
53
F/ROUT
O
Forward/reverse control signal output to the CXA2509AQ (IC301)
“L”: reverse direction, “H”: forward direction
“L”: reverse direction, “H”: forward direction
54
MTLON
O
METAL control in/out terminal
At initial mode: valid/invalid selection input of METAL function (valid at “L” input)
At normal mode: METAL on/off control signal output to the CXA2509AQ (IC301)
(METAL on at “H” output)
At initial mode: valid/invalid selection input of METAL function (valid at “L” input)
At normal mode: METAL on/off control signal output to the CXA2509AQ (IC301)
(METAL on at “H” output)
55
TAPATT
O
Tape muting on/off control signal output to the CXA2509AQ (IC301) “H”: muting on
Active at ATA, FF/REW mode
Active at ATA, FF/REW mode
56
NCO
I/O
Dolby control in/out terminal Not used (pull down)
57
AMSIN
I
Whether a music is present or not from CXA2509AQ (IC301) is detected at auto music sensor
“L”: music is present, “H”: music is not present
“L”: music is present, “H”: music is not present
58
4VPRE
I
4V PREOUT setting terminal “L”: 4V PREOUT on Fixed at “H” in this set
59
VOLATT
O
Pre amplifier muting on/off control signal output to the electrical volume (IC331)
“L”: muting on
“L”: muting on
60 to 64
NCO
O
Not used (open)
65
FLASH_W
I
Internal flash memory data write mode detection signal input terminal “L”: data write mode
Not used (open)
Not used (open)
66
TESTIN
I
Setting terminal for the test mode “L”: test mode, normally fixed at “H”
67
RCIN1
I
Rotary remote commander shift key input terminal “L”: shift key on
68 to 73
NCO
O
Not used (open)
74
EEP_SIO
I/O
Two-way data bus for tuner EEPROM with the FM/AM tuner unit (TU1)
75
EEP_CKO
I/O
Two-way bus clock signal for tuner EEPROM with the FM/AM tuner unit (TU1)
76
COLSEL
I
Setting terminal for the illumination color
“L”: amber, “H”: green Fixed at “L” in this set
“L”: amber, “H”: green Fixed at “L” in this set
77
SWSHIFT
O
VCO shift control signal output to the FM/AM tuner unit (TU1) for SW
“L”: EXCEPT SW, “H”: SW
“L”: EXCEPT SW, “H”: SW
78
DOORSW
I
Front panel open/close detection signal input “L” is input when the front panel is closed
79
DOORIND
O
LED drive signal output of the MD disc slot illumination and Z indicator (LED810, LSW810)
“H”: LED on “H” is output to turn on the LED when front panel is opened
“H”: LED on “H” is output to turn on the LED when front panel is opened
80, 81
RE IN1, RE IN0
I
Dial pulse input of the rotary encoder (RE501) (for VOLUME control)
82
XKEYON
O
A/D converter power control signal output terminal
When the KEYACK (pin wh) that controls reference voltage power for key A/D conversion input
is active, “L” is output from this terminal to enable the input
When the KEYACK (pin wh) that controls reference voltage power for key A/D conversion input
is active, “L” is output from this terminal to enable the input
83
ILLON
O
Power on/off control signal output of the illumination LED and liquid crystal display driver
(IC501) “H”: power on
(IC501) “H”: power on
84
REL
I
Rotation detection signal input from supply reel sensor and take-up reel sensor on the mechanism
deck
deck
•
MAIN BOARD IC501 MN101C49KTE (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Description
1
VREF–
I
Reference voltage (0V) input terminal (for A/D converter)
2
VSM
I
FM and AM signal meter voltage detection signal input from the FM/AM tuner unit (TU1)
(A/D input)
(A/D input)
3
NIL
I
Not used (fixed at “L”)
4
KEYIN1
I
Key input terminal (A/D input) LSW502 to LSW510, LSW514
(MENU, DISC/PRESET+, DISC/PRESET–, > SEEK+ M, . SEEK– m, SOUND,
ENTER, DSPL, LIST, MODE o keys input)
(MENU, DISC/PRESET+, DISC/PRESET–, > SEEK+ M, . SEEK– m, SOUND,
ENTER, DSPL, LIST, MODE o keys input)
5
KEYIN0
I
Key input terminal (A/D input) LSW501, LSW513, LSW515 to LSW522 (OFF, SOURCE, EQ7,
MBP, 6, 5, 4, 3, SHUF 2, REP 1 keys input)
MBP, 6, 5, 4, 3, SHUF 2, REP 1 keys input)
6
RCIN0
I
Rotary remote commander key input terminal (A/D input)
7, 8
NIL
I
Not used (fixed at “L”)
9
DSTSEL
I
Destination setting terminal (A/D input) Fixed at center voltage in this set
10
VREF+
I
Reference voltage (+5V) input terminal (for A/D converter)
11
VDD
—
Power supply terminal (+5V)
12
OSCOUT
O
Main system clock output terminal (18.432 MHz)
13
OSCIN
I
Main system clock input terminal (18.432 MHz)
14
VSS
—
Ground terminal
15
XI
I
Sub system clock input terminal (32.768 kHz)
16
XO
O
Sub system clock output terminal (32.768 kHz)
17
MMOD
I
Selection signal of memory mode input terminal “L”:single chip mode (fixed at “L”)
18
LCDSO
O
Serial data output to the liquid crystal display driver (IC501)
19
LCDCE
O
Chip enable signal output to the liquid crystal display driver (IC501) “H” active
20
LCDCKO
O
Serial data transfer clock signal output to the liquid crystal display driver (IC501)
21 to 23
NCO
O
Not used (open)
24
SYSRST
O
Reset signal output to the SONY bus interface (IC581) “L”: reset
25
BUSON
O
Bus on/off control signal output to the SONY bus interface (IC581) “L”: bus on
26
KEYACK
I
Input of acknowledge signal for the key entry Acknowledge signal is input to accept function
and eject keys in the power off status On at input of “H”
and eject keys in the power off status On at input of “H”
27
NIL
I
Not used (fixed at “L”)
28
BUIN
I
Battery detection signal input from the SONY bus interface (IC581)
“L” is input at low voltage
“L” is input at low voltage
29
SIRCS
I
SIRCS remote control signal input terminal Not used (open)
30, 31
NIL
I
Not used (fixed at “L”)
32
NIH
I
Not used (fixed at “H”)
33
RESET
I
System reset signal input from the reset signal generator (IC551) and reset switch (S551)
“L”: reset “L” is input for several 100 msec after power on, then it changes to “H”
“L”: reset “L” is input for several 100 msec after power on, then it changes to “H”
34
TUNON
O
Tuner system power supply on/off control signal output “H”: tuner power on
35
BEEP
O
Beep sound drive signal output to the power amplifier (IC751)
36
PW_ON
O
Main system power supply on/off control signal output “H”: power on
37
NCO
O
Not used (open)
38
ACCIN
I
Accessory detection signal input “L”: accessory on
39
NCO
O
Not used (open)
40
TELATT
I
Telephone attenuate signal input At input of “H”, the signal is attenuated by –20 dB
41
NIH
I
Not used (fixed at “H”)
42
BUSSO
O
Serial data output to the SONY bus interface (IC581)
43
BUSSI
I
Serial data input from the SONY bus interface (IC581)
Click on the first or last page to see other XR-CA600X / XR-CA620X service manuals if exist.