Read Sony XR-CA360EE Service Manual online
4
XR-CA360EE
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms,
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid its damage.
avoid its damage.
• Do not connect the speaker terminals to the car
chassis, or connect the terminals of the right
speakers with those of the left speaker.
speakers with those of the left speaker.
• Do not connect the earth lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active
• Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
terminals may damage the unit.
• To avoid a malfunction, do not use the built-in
speaker wires installed in your car if the unit shares
a common negative (–) lead for the right and left
speakers.
a common negative (–) lead for the right and left
speakers.
• Do not connect the unit’s speaker cords to each
other.
Precautions
•Choose the installation location carefully so
that the unit will not interfere with normal
driving operations.
driving operations.
•Avoid installing the unit in areas subject to
dust, dirt, excessive vibration, or high
temperatures, such as in direct sunlight or near
heater ducts.
temperatures, such as in direct sunlight or near
heater ducts.
•Use only the supplied mounting hardware for
a safe and secure installation.
Mount ing angle adjust ment
Adjust the mounting angle to less than 20°.
Removing the protection collar
and the bracket (4)
and the bracket (4)
Before installing the unit, remove the
protection collar 4 and the bracket 1 from
the unit.
protection collar 4 and the bracket 1 from
the unit.
1
Remove the protection collar 4.
1 Engage the release keys 7 together with
1 Engage the release keys 7 together with
the protection collar 4.
2 Pull out the release keys 7 to remove the
protection collar 4.
2
Remove the bracket 1.
1 Insert both release keys 7 together
1 Insert both release keys 7 together
between the unit and the bracket 1 until
they click.
they click.
2 Pull down the bracket 1, then pull up the
unit to separate.
Mounting example (5)
Installation in the dashboard
Notes
• Bend these claws outward for a tight fit, if
• Bend these claws outward for a tight fit, if
necessary (5-2).
• Make sure that the 4 catches on the protection
collar 4 are properly engaged in the slots of the
unit (5-3).
unit (5-3).
A
BUS AUDIO IN
BUS CONTROL IN
AUDIO OUT
REAR
BUS AUDIO IN
BUS CONTROL IN
Source selector*
Селектор источника*
Селектор источника*
XA-CA30
* not supplied
не прилагается
2
B
Cautions
• This unit is designed for negative earth 12 V
DC operation only.
• Do not get the wires under a screw, or caught
in moving parts (e.g. seat railing).
• Before making connections, turn the car
ignition off to avoid short circuits.
• Connect the power connecting cord 6 to the
unit and speakers before connecting it to the
auxiliary power connector.
auxiliary power connector.
• Run all earth wires to a common earth
point.
• Be sure to insulate any loose unconnected
wires with electrical tape for safety.
Notes on the power supply cord (yellow)
• When connecting this unit in combination with
• When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
circuit’s rating must be higher than the sum of
each component’s fuse.
• When no car circuits are rated high enough,
connect the unit directly to the battery.
Connection diagram (3)
A To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
This connection is only for amplifiers. Connecting
any other system may damage the unit.
Warning
If you have a power aerial without a relay box,
connecting this unit with the power connecting
cord 6 may damage the aerial.
connecting this unit with the power connecting
cord 6 may damage the aerial.
Notes on the control leads
• The power aerial control lead (blue) supplies +12 V
• The power aerial control lead (blue) supplies +12 V
DC when you turn on the tuner.
• When your car has built-in FM/AM aerial in the
rear/side glass, connect the power aerial control
lead (blue) or the accessory power input lead (red)
to the power terminal of the existing aerial
booster. For details, consult your dealer.
lead (blue) or the accessory power input lead (red)
to the power terminal of the existing aerial
booster. For details, consult your dealer.
• A power aerial without a relay box cannot be used
with this unit.
Memory hold connection
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition switch is turned off.
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition switch is turned off.
Caution
Handle the bracket 1 carefully to avoid injuring
your fingers.
your fingers.
1
Catch
Note
Before installing, make sure that the catches on
both sides of the bracket 1 are bent inwards 2 mm.
If the catches are straight or bent outwards, the unit
will not be installed securely and may spring out.
Before installing, make sure that the catches on
both sides of the bracket 1 are bent inwards 2 mm.
If the catches are straight or bent outwards, the unit
will not be installed securely and may spring out.
Connection example (2)
Notes (2-B-
)
• Be sure to connect the earth cord before
connecting the amplifier.
• If you connect an optional power amplifier and do
not use the built-in amplifier, the beep sound will
be deactivated.
be deactivated.
Tip (2-B-
)
For connecting two or more CD/MD changers, the
source selector XA-C30 (optional) is necessary.
source selector XA-C30 (optional) is necessary.
Mounting the unit in a Japanese
car (6)
car (6)
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.
makes of Japanese cars. In such a case, consult
your Sony dealer.
Note
To prevent malfunction, install only with the
supplied screws 8.
To prevent malfunction, install only with the
supplied screws 8.
How to detach and attach the
front panel (7)
front panel (7)
Before installing the unit, detach the front
panel.
panel.
7-A To detach
Before detaching the front panel, be sure to
press
press
(OFF).
Press
(RELEASE), then slide the front panel to
the left, and pull it off towards you.
7-B To attach
Attach part A of the front panel to part B of the
unit as illustrated and push the left side into
position until it clicks.
unit as illustrated and push the left side into
position until it clicks.
Warning when installing in a car
without ACC (accessory)
position on the ignition key
switch
without ACC (accessory)
position on the ignition key
switch
Be sure to press
(OFF) on the unit for 2
seconds to turn off the clock display after
turning off the engine.
When you press
turning off the engine.
When you press
(OFF) only momentarily, the
clock display does not turn off and this causes
battery wear.
battery wear.
RESET button
When the installation and connections are
completed, be sure to press the RESET button
with a ballpoint pen, etc., after detaching the
front panel.
completed, be sure to press the RESET button
with a ballpoint pen, etc., after detaching the
front panel.
Power connection diagram
Auxiliary power connector may vary depending
on the car. Check your car’s auxiliary power
connector diagram to make sure the connections
match correctly. There are three basic types
(illustrated below). You may need to switch the
positions of the red and yellow leads in the car
stereo’s power connecting cord.
After matching the connections and switched
power supply leads correctly, connect the unit to
the car’s power supply. If you have any
questions and problems connecting your unit
that are not covered in this manual, please
consult the car dealer.
on the car. Check your car’s auxiliary power
connector diagram to make sure the connections
match correctly. There are three basic types
(illustrated below). You may need to switch the
positions of the red and yellow leads in the car
stereo’s power connecting cord.
After matching the connections and switched
power supply leads correctly, connect the unit to
the car’s power supply. If you have any
questions and problems connecting your unit
that are not covered in this manual, please
consult the car dealer.
Click on the first or last page to see other XR-CA360EE service manuals if exist.