Read Sony XR-C2200 / XR-C2300X Service Manual online
12
AM Auto Seek/Stop Level Check
Make this adjustment after “FM Auto Seek/Stop Level Adjust-
ment”.
Setting:
ment”.
Setting:
[SOURCE] t [MODE] button: AM
Procedure:
1. Set to the test mode. (See page 10)
2. Push the [SOURCE] button and set to FM.
3. Push the [MODE] button and set to AM.
1. Set to the test mode. (See page 10)
2. Push the [SOURCE] button and set to FM.
3. Push the [MODE] button and set to AM.
Display
4. Check that the “AM” indication turns to “AM0” indication on
the display window.
Display
AM RF signal
generator
Carrier frequency : 1,000 kHz
30% amplitude
modulation by
1 kHz signal
Output level
30% amplitude
modulation by
1 kHz signal
Output level
: 30 dB (44.7
µ
V)
(50
Ω
)
set
AM dummy antenna
30
Ω
15 pF
65 pF
antenna jack (CN100)
SHUF
SHUF
Adjustment Location: See page 13.
FM Stereo
Level meter
Level meter
signal generator
connection
reading (dB)
output channel
L-CH
L-CH
A
B
R-CH
L-CH
Adjust RV1 on TU100
for minimum reading.
R-CH
R-CH
C
D
L-CH
R-CH
Adjust RV1 on TU100
for minimum reading.
L-CH Stereo separation: A-B
R-CH Stereo separation: C-D
The separations of both channels should be equal.
R-CH Stereo separation: C-D
The separations of both channels should be equal.
Specification: Separation more than 26 dB
Adjustment Location: See page 13.
Procedure:
FM Stereo Separation Adjustment
Setting:
[SOURCE] button: FM
FM RF signal
generator
Carrier frequency : 98.1 MHz
Output level
Output level
: 70 dB (3.2 mV)
Mode
: stereo
Modulation
: main: 1 kHz, 33.75 kHz deviation (45%)
sub: 1 kHz, 33.75 kHz deviation (45%)
sub: 1 kHz, 33.75 kHz deviation (45%)
:
19 kHz pilot: 7.5 kHz deviation (10%)
0.01
µ
F
set
antenna jack (CN100)
+
–
–
AUDIO OUT jack (CN400)
level meter
10 k
Ω
SHUF
3. Adjust with the volume RV2 on TU100 so that the “FM” indi-
cation turns to “FM0” indication on the display window.
But, in case of already indicated “FM0”, turn the RV2 so that
put out light “0” indication and adjustment.
But, in case of already indicated “FM0”, turn the RV2 so that
put out light “0” indication and adjustment.
Display
Adjustment Location: See page 13.
TUNER SECTION
0 dB=1 µV
Note:
Adjust the tuner section in the sequence shown below.
1. FM Auto Seek/Stop Level Adjustment
2. FM Stereo Separation Adjustment
3. AM Auto Seek/Stop Level Check
2. FM Stereo Separation Adjustment
3. AM Auto Seek/Stop Level Check
FM Auto Seek/Stop Level Adjustment
Setting:
[SOURCE] button: FM
FM RF signal
generator
Carrier frequency
: 97.9 MHz
Output level
: 22 dB (12.6
µ
V)
Mode
: mono
Modulation
: 1 kHz, 22.5 kHz deviation (30%)
0.01
µ
F
set
antenna jack (CN100)
SHUF
Cautions during repair
When the tuner unit is defective, replace it by a new one be-
cause its internal block is difficult to repair.
cause its internal block is difficult to repair.
Procedure:
1. Set to the test mode. (See page 10)
2. Push the [SOURCE] button and set to FM.
1. Set to the test mode. (See page 10)
2. Push the [SOURCE] button and set to FM.
Display
Click on the first or last page to see other XR-C2200 / XR-C2300X service manuals if exist.