Read Sony XR-3100R / XR-C33R Service Manual online
33
Pin No.
Pin Name
I/O
Description
75
DAVN
I
Data transmit completed detect signal input from the RDS decoder (IC51) “H” active
76
KEYACK
I
Input of acknowledge signal for the key entry Acknowledge signal is input to accept function
and eject keys in the power off status On at input of “H”
and eject keys in the power off status On at input of “H”
77
BU-IN
I
Battery detect signal input from the SONY bus interface (IC701) and battery detect circuit
“L” is input at low voltage IC701: Used for the XR-C33R only
“L” is input at low voltage IC701: Used for the XR-C33R only
78
ILL IN
I
Auto dimmer control illumination line detection signal input terminal
“L” is input at dimmer detection Fixed at “L” in this set
“L” is input at dimmer detection Fixed at “L” in this set
79
TEL-ATT
I
Telephone muting signal input terminal At input of “H”, the signal is attenuated by –20 dB
Not used (open)
Not used (open)
80
NOSESW
I
Front panel block remove/attach detection signal input terminal
“L”: front panel is attached
“L”: front panel is attached
81
ACC IN
I
Accessory detect signal input terminal “L”: accessory on
82 to 85
NCO
O
Not used (open)
86
HSTX
I
Hardware standby input terminal “L”: hardware standby mode Reset signal input in this set
87
MD2
I
Setting terminal for the CPU operational mode (fixed at “L” in this set)
88, 89
MD1, MD0
I
Setting terminal for the CPU operational mode (fixed at “H” in this set)
90
RESET
I
System reset signal input from the reset signal generator (IC652) and reset switch (S503)
“L”: reset “L” is input for several 100 msec after power on, then it changes to “H”
“L”: reset “L” is input for several 100 msec after power on, then it changes to “H”
91
VSS
—
Ground terminal
92
X0
I
Main system clock input terminal (3.68 MHz)
93
X1
O
Main system clock output terminal (3.68 MHz)
94
VCC
—
Power supply terminal (+5V)
95 to 99
NCO
O
Not used (open)
100
9K/10K
I
AM frequency step (9 kHz or 10 kHz) selection signal input terminal
“L”: 9 kHz, “H”: 10 kHz Not used (open)
“L”: 9 kHz, “H”: 10 kHz Not used (open)
101
NCO
O
Not used (open)
102
MTLIN
I
Auto metal detection signal input terminal “L”: auto metal Fixed at “L” in this set
103
AMSIN
I
Whether a music is present or not from CXA2509AQ (IC301) is detected at auto music sensor
“L”: music is present, “H”: music is not present
“L”: music is present, “H”: music is not present
104
REEL
I
Rotation detect signal input from supply reel sensor and take-up reel sensor on the deck
mechanism
mechanism
105
POS0
I
106
POS1
I
107
POS2
I
108
POS3
I
109
LM-EJ
O
Motor drive signal output to the loading/tape operation motor drive (IC361) “H” active
(For the eject direction and reverse side operation) *1
(For the eject direction and reverse side operation) *1
110
LM-LOD
O
Motor drive signal output to the loading/tape operation motor drive (IC361) “H” active
(For the loading direction and forward side operation) *1
(For the loading direction and forward side operation) *1
111
CM-ON
O
Capstan/reel motor (M901) drive signal output terminal “H”: motor on
112
TAPEON
O
Tape system power supply on/off control signal output terminal “H”: tape on
113
N-ROUT
O
Forward/reverse direction control signal output to the CXA2509AQ (IC301)
“L”: forward direction, “H”: reverse direction
“L”: forward direction, “H”: reverse direction
114
AMSON
O
Tape auto music sensor control signal output to the CXA2509AQ (IC301)
“L” is output to lower the gain for audio level at FF/REW mode
“L” is output to lower the gain for audio level at FF/REW mode
115
MTLON
I/O
Tape position (EJECT/FF/REW/
REV/FWD mode) detect input from
the tape operation switch on the deck
mechanism
REV/FWD mode) detect input from
the tape operation switch on the deck
mechanism
POS0: “L”: EJECT mode, “H”: others mode
POS1: “L”: FF and FWD mode, “H”: others mode
POS2: “L”: REW mode, “H”: others mode
POS3: “L”: REV and EJECT mode, “H”: others mode
POS1: “L”: FF and FWD mode, “H”: others mode
POS2: “L”: REW mode, “H”: others mode
POS3: “L”: REV and EJECT mode, “H”: others mode
METAL control in/out terminal
At initial mode: auto/manual mode selection input of METAL function (manual at “L” input)
At manual mode: METAL on/off control signal output terminal (METAL on at “H” output)
At auto mode: input at MTLIN (pin <z/x)
At initial mode: auto/manual mode selection input of METAL function (manual at “L” input)
At manual mode: METAL on/off control signal output terminal (METAL on at “H” output)
At auto mode: input at MTLIN (pin <z/x)
Click on the first or last page to see other XR-3100R / XR-C33R service manuals if exist.