Read Sony XR-1300R / XR-C2300R Service Manual online
25
5-8.
IC PIN FUNCTION DESCRIPTION
•
MAIN BOARD IC1 MB90574PMT-G-268-BND (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Description
1
SEEKOUT
O
Seek control signal output to the FM/AM tuner unit (TU100)
AM mode: Used for IF count output/SD output request/AGC cut at SEEK or BTM
FM mode: Used for SD speed up at SEEK, BTM, or AF
“L” is output at tuner off
AM mode: Used for IF count output/SD output request/AGC cut at SEEK or BTM
FM mode: Used for SD speed up at SEEK, BTM, or AF
“L” is output at tuner off
2
AFSEEK
O
PLL low-pass filter time constant selection signal output at AF SEEK
“H” is output when AF SEEK Not used (open)
“H” is output when AF SEEK Not used (open)
3
NC
O
Not used (open)
4
ST-IND
I/O
FM stereo broadcasting detection signal input from the FM/AM tuner unit (TU100), or forced
monaural control signal output to the FM/AM tuner unit (TU100)
“L” is input in the FM stereo mode, or “L” is output in the forced monaural mode
monaural control signal output to the FM/AM tuner unit (TU100)
“L” is input in the FM stereo mode, or “L” is output in the forced monaural mode
5
TUMUTE
O
Muting on/off control signal output of the FM and AM tuner signal “H”: muting on
6
FM-ON
O
FM system power supply on/off control signal output terminal
“L”: AM power on, “H”: FM power on
“L”: AM power on, “H”: FM power on
7
TU-ON
O
Tuner system power supply on/off control signal output terminal “H”: tuner power on
8
VCC
—
Power supply terminal (+5V)
9
NC
O
Not used (open)
10
BUSON
O
Bus on/off control signal output to the SONY bus interface (IC800) “L”: bus on
Used for the XR-C2300R only
Used for the XR-C2300R only
11
SYSRST
O
Reset signal output to the SONY bus interface (IC800) “L”: reset
Used for the XR-C2300R only
Used for the XR-C2300R only
12
NOSESW
I
Front panel block remove/attach detection signal input terminal
“L”: front panel is attached
“L”: front panel is attached
13
LCDSO
O
Serial data output to the liquid crystal display driver (IC900)
14
LCD CKO
O
Serial data transfer clock signal output to the liquid crystal display driver (IC900)
15
BEEP
O
Beep sound drive signal output terminal
16
SD-IN
I
Signal detector input from the FM/AM tuner unit (TU100)
Stop level for SEEK, SCAN, etc. is determined SD is present at input of “H”
Stop level for SEEK, SCAN, etc. is determined SD is present at input of “H”
17
UNISI
I
Serial data input from the SONY bus interface (IC800) Used for the XR-C2300R only
18
UNISO
O
Serial data output to the SONY bus interface (IC800) Used for the XR-C2300R only
19
UNICKO
O
Serial data transfer clock signal output to the SONY bus interface (IC800)
Used for the XR-C2300R only
Used for the XR-C2300R only
20
VOL-CE
O
Chip enable signal output to the electrical volume (IC400)
21
VOL-SO
O
Serial data output to the electrical volume (IC400)
22
VOL-CKO
O
Serial data transfer clock signal output to the electrical volume (IC400)
23, 24
NC
O
Not used (open)
25
PLLSI
I
PLL serial data input from the FM/AM PLL (IC130)
26
PLLSO
O
PLL serial data output to the FM/AM PLL (IC130)
27
PLLCKO
O
PLL serial data transfer clock signal output to the FM/AM PLL (IC130)
28
PLLCE
O
PLL chip enable signal output to the FM/AM PLL (IC130) “H” active
29
ILL-ON
O
Power on/off control signal output of the illumination LED and liquid crystal display driver
(IC900) “H”: power on
(IC900) “H”: power on
30, 31
NC
O
Not used (open)
32
NOISE-ON
O
Discharge control signal output for the noise detection circuit “H”: discharge
33
VSS
—
Ground terminal
34
C
—
Connected to coupling capacitor for the power supply
35
AD-ON
O
A/D converter power control signal output terminal
When the KEYACK (pin uh) that controls reference voltage power for key A/D conversion input
is active, “L” is output from this terminal to enable the input
When the KEYACK (pin uh) that controls reference voltage power for key A/D conversion input
is active, “L” is output from this terminal to enable the input
Click on the first or last page to see other XR-1300R / XR-C2300R service manuals if exist.