Read Sony XAV-V630BT Service Manual online
XAV-V630BT
14
To capture your voice during handsfree calling, you
need to install the microphone ʕ.
need to install the microphone ʕ.
Cautions
ˎ It is extremely dangerous if the cord becomes
wound around the steering column or gearstick.
Be sure to keep it and other parts from interfering
with your driving operations.
Be sure to keep it and other parts from interfering
with your driving operations.
ˎ If airbags or any other shock-absorbing
equipment are in your car, contact the store
where you purchased this unit, or the car dealer,
before installation.
where you purchased this unit, or the car dealer,
before installation.
Installing the microphone
ʖ
ʕ
Clip (not supplied)
ʕ
Make sure your car’s auxiliary power connector and
match the connections of cords correctly
depending on the car.
match the connections of cords correctly
depending on the car.
Common connection
When the positions of the red and yellow
leads are inverted
leads are inverted
For cars without ACC position
After matching the connections and switching
power supply leads correctly, connect the unit to
the car’s power supply. If you have any questions
and problems connecting your unit that are not
covered in this manual, consult the car dealer.
power supply leads correctly, connect the unit to
the car’s power supply. If you have any questions
and problems connecting your unit that are not
covered in this manual, consult the car dealer.
Power connection diagram
12
continuous power
supply
supply
Yellow
15
switched power supply
Red
12
switched power supply Yellow
15
continuous power
supply
supply
Red
Auxiliary power connector
Red
Red
Yellow
Yellow
Red
Red
Yellow
Yellow
Red
Red
Yellow
Yellow
Installation
Before installing the unit, remove the bracket ʗ
from the unit.
from the unit.
1
Insert the release keys ʘ into the
catches between the unit and the
bracket ʗ at the same time until they
click.
catches between the unit and the
bracket ʗ at the same time until they
click.
2
Pull down the bracket ʗ, then pull up
the unit to separate them.
the unit to separate them.
Removing the bracket
ʘ
ʗ
Catch
Face the hook inwards.
When using the steering wheel remote
control
control
Installation of the connection cable RC-SR1 (not
supplied) is required before use.
supplied) is required before use.
1
To enable the steering wheel remote control, select
[General Settings] q [User Defined] to make the
registration (page 19).
When the registration is complete, the steering
wheel remote control becomes available.
[General Settings] q [User Defined] to make the
registration (page 19).
When the registration is complete, the steering
wheel remote control becomes available.
Notes on installing the connection cable RC-SR1 (not
supplied)
supplied)
ˎ Refer to the support sites on the back cover for
details, then connect each lead properly to the
appropriate leads. Making an improper connection
may damage the unit.
appropriate leads. Making an improper connection
may damage the unit.
ˎ Consulting the dealer or an experienced technician
for help is recommended.
When using the wired remote control
1
To enable the wired remote control, set [Steering
Control] in [General Settings] to [Preset] (page 19).
Control] in [General Settings] to [Preset] (page 19).
Installation of the rearview camera (not supplied) is
required before use.
The image of a rearview camera connected to the
CAMERA IN terminal is displayed when:
required before use.
The image of a rearview camera connected to the
CAMERA IN terminal is displayed when:
ˋ the back lamp of your car lights up (or the shift
lever is set to the R (reverse) position).
ˋ you press HOME, then touch [Rear Camera].
ˋ you press and hold DSPL then touch [Rear
Camera] if [SOURCE Key Func.] is set to [DSPL]
(
(
)
Using the wired remote control
Using the rearview camera
Mounting the unit in a Japanese car
You may not be able to install this unit in some
Japanese cars. In such a case, consult your Sony
dealer.
Japanese cars. In such a case, consult your Sony
dealer.
When mounting this unit to the preinstalled
brackets of your car, use the supplied screws ʔ in
the appropriate screw holes based on your car: T
for TOYOTA, M for MITSUBISHI and N for NISSAN.
brackets of your car, use the supplied screws ʔ in
the appropriate screw holes based on your car: T
for TOYOTA, M for MITSUBISHI and N for NISSAN.
Note
To prevent a malfunction, install only with the supplied
screws ʔ.
To prevent a malfunction, install only with the supplied
screws ʔ.
ʔ
To the dashboard/center console
Parts supplied with your
car
car
ʔ
Bracket
Bracket
1
Position the bracket ʗ inside the
dashboard, then bend the claws outward
for a tight fit.
dashboard, then bend the claws outward
for a tight fit.
2
Mount the unit onto the bracket ʗ.
Note
If the catches are straight or bent outwards, the unit will
not be installed securely and may spring out.
If the catches are straight or bent outwards, the unit will
not be installed securely and may spring out.
Catch
ʗ
Larger than
182 mm (7
182 mm (7
1
/
4
in)
Larger than
111 mm (4
111 mm (4
3
/
8
in)
ʙ
ʗ
When replacing the fuse, be sure to
use one matching the amperage
rating stated on the original fuse. If
the fuse blows, check the power
connection and replace the fuse. If
the fuse blows again after
replacement, there may be an
internal malfunction. In such a case, consult your
nearest Sony dealer.
use one matching the amperage
rating stated on the original fuse. If
the fuse blows, check the power
connection and replace the fuse. If
the fuse blows again after
replacement, there may be an
internal malfunction. In such a case, consult your
nearest Sony dealer.
Fuse replacement
Fuse (10 A)
Note
Before attaching the double-sided tape ʖ, clean the
surface of the dashboard with a dry cloth.
Before attaching the double-sided tape ʖ, clean the
surface of the dashboard with a dry cloth.
When mounting in a Japanese car, see “Mounting
the unit in a Japanese car” (page 37).
the unit in a Japanese car” (page 37).
Mounting the unit with the supplied
bracket
bracket
Before installing, make sure the catches on both
sides of the bracket ʗ are bent inwards 3.5 mm
(
sides of the bracket ʗ are bent inwards 3.5 mm
(
5
/
32
in).
Mounting the unit in the dashboard
.
.
.
.
Click on the first or last page to see other XAV-V630BT service manuals if exist.