Read Sony XAV-77 Service Manual online
5
XAV-77
8
Location of Controls
Main unit
Monitor closed
1
1
3
3
2
2
4
4
5
5
6
6
7
7
8
8
9
9
0
0
qa
q
1
DISC –/+ buttons
2
Reset button
3
Sensor for card remote commander
4
VOL (volume adjust) –/+ buttons
5
SEEK/AMS –/+ buttons
1
ANGLE (monitor angle adjust) –/+ buttons
2
Sensor for card remote commander
6
Display window
7
OFF (Standby/Power off) button*
8
OPEN/CLOSE button
9
ATT button
0
MODE button
qa
SOURCE (Power on/Radio/CD/MD/VIDEO or TV)
button
Monitor opened up
1
1
2
2
* Warning when installing in a car without an ACC (accessory) position on the ignition key
After turning off the ignition, be sure to hold down OFF on the unit until the display disappears.
Otherwise, the clock display does not turn off and this causes battery drain.
Otherwise, the clock display does not turn off and this causes battery drain.
9
Card remote commander
The unit can be operated with the card remote commander.
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
0
qa
qd
qs
qf
qg
1
DSPL (display mode change) button
2
Number buttons
3
DSO button
4
MENU button
5
SOURCE (Power on/Radio/CD/MD/VIDEO/TV)
button
6
B/b SEEK/AMS –/+ buttons
7
SOUND button
8
OFF (Standby/Power off) button
9
VOL (volume adjust) +/– buttons
0
EQ7 button
qa
MODE button
qs
LIST button
qd
V/v DISC +/– buttons
qf
ENTER button
qg
ATT button
Note
If the unit is turned off by holding down OFF, it cannot be operated with the card remote commander unless SOURCE
on the unit is pressed to activate the unit first.
If the unit is turned off by holding down OFF, it cannot be operated with the card remote commander unless SOURCE
on the unit is pressed to activate the unit first.
Tip
See “Replacing the lithium battery” for details on how to replace the battery (page 46).
See “Replacing the lithium battery” for details on how to replace the battery (page 46).
16
Setting the Clock
This unit uses 12-hour time indication.
To set the clock, use the card remote commander while the
monitor is open.
To set the clock, use the card remote commander while the
monitor is open.
1
Press MENU.
Press
V or v to select “Clock”.
C l o c k
2
Press ENTER.
C l o c k
1 : 0 0
1
Press
V or v to set the hours.
2
Press
b to move to the minutes, and press V or v to set
the minutes.
V: increases the value
v: decreases the value
3
Press ENTER.
The regular display appears again.
ENTER
MENU
V/v
B/b
Tip
When “Dual Information” is set to “on”,
the time is always displayed (page 41).
When “Dual Information” is set to “on”,
the time is always displayed (page 41).
5
Installation angle
The unit should be installed within an
angle of 25 degrees from horizontal. If
this angle is exceeded, the monitor may
not open up or retract properly.
The unit should be installed within an
angle of 25 degrees from horizontal. If
this angle is exceeded, the monitor may
not open up or retract properly.
Note
Keep the units and connection cables
apart.
The Media Center main unit and the
connection box 1 should not be in close
proximity.
Keep the units and connection cables
apart.
The Media Center main unit and the
connection box 1 should not be in close
proximity.
1
Installing the Main Unit
Before installation
This unit is designed to be completely safe, but if not installed
correctly, it can cause accidents. Be sure to verify the following
points before installation.
Install the main unit to the in-dash location, and the connection
box under the navigator’s seat, etc.
• If the monitor in the opened position is close to a air-
correctly, it can cause accidents. Be sure to verify the following
points before installation.
Install the main unit to the in-dash location, and the connection
box under the navigator’s seat, etc.
• If the monitor in the opened position is close to a air-
conditioning outlet, the outlet should be closed.
• Install the unit so that the monitor when opened up will not
block access to the hazard switch or other important controls.
• Do not install the unit (monitor) in locations which may be
subject to excessively low or high temperatures. (Otherwise the
unit may be deformed and the LCD may be damaged.)
Exposure to direct sunlight can also lead to high temperatures
and should be avoided.
unit may be deformed and the LCD may be damaged.)
Exposure to direct sunlight can also lead to high temperatures
and should be avoided.
Selecting the installation location
1
Set the ignition key to OFF or remove it.
2
Place the units in their intended mounting
locations to check the cable length and monitor
installation conditions.
locations to check the cable length and monitor
installation conditions.
Frequency select switch
The AM (FM) tuning interval is factory-set to the 9 k (50 k)
position. If the frequency allocation system of your country is
based on 10 kHz (200 kHz) interval, set the switch on the bottom
of the unit to the 10 k (200 k) position before making connections.
The AM (FM) tuning interval is factory-set to the 9 k (50 k)
position. If the frequency allocation system of your country is
based on 10 kHz (200 kHz) interval, set the switch on the bottom
of the unit to the 10 k (200 k) position before making connections.
FM 200k
AM 10k
FM 50k
AM 9k
Frequency select switch
SECTION 2
GENERAL
This section is extracted from
instruction manual.
instruction manual.
Click on the first or last page to see other XAV-77 service manuals if exist.