Read Sony XAV-70BT / XAV-E70BT Service Manual online
XAV-70BT/E70BT
4
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
static break-down because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
IMPORTANT NOTE FOR REPAIRING
This set contain individual information that the customer regis-
tered because it installs the Bluetooth function.
When repairing, the data that the customer registered might disap-
pear. Have the approval of the customer beforehand.
If any of the following parts was replaced, that data disappears.
•
This set contain individual information that the customer regis-
tered because it installs the Bluetooth function.
When repairing, the data that the customer registered might disap-
pear. Have the approval of the customer beforehand.
If any of the following parts was replaced, that data disappears.
•
Complete LCD board
•
IC1102 on the LCD board
• Initialize
Note: Exchanged old complete LCD board and old IC1102 are destroyed
with the hammer, and throw away.
NOTE THE IC4, IC11 AND IC13 ON THE SERVO
BOARD REPLACING
IC4, IC11 and IC13 on the SERVO board cannot exchange with
single. When these parts are damaged, exchange the entire mount-
ed board.
BOARD REPLACING
IC4, IC11 and IC13 on the SERVO board cannot exchange with
single. When these parts are damaged, exchange the entire mount-
ed board.
NOTE THE IC1201 ON THE LCD BOARD REPLACING
IC1201 on the LCD board cannot exchange with single. When this
part is damaged, exchange the entire mounted board.
IC1201 on the LCD board cannot exchange with single. When this
part is damaged, exchange the entire mounted board.
NOTE FOR REPLACEMENT OF THE KEY BOARD
When repairing, the complete KEY board (Part No. A-1748-
651-A) should be replaced since any parts in the KEY board can-
not be repaired.
When repairing, the complete KEY board (Part No. A-1748-
651-A) should be replaced since any parts in the KEY board can-
not be repaired.
NOTE FOR REPLACING THE COMPLETE AUDIO
BOARD
If the complete AUDIO board was replaced, be sure to refer to
Technical News published separately.
BOARD
If the complete AUDIO board was replaced, be sure to refer to
Technical News published separately.
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
•
Strong viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
Label indication
Destination
Signal format
system
Region
code
Part No.
NTSC
1
4-163-711-0[]
US and Canadian models
PAL
2
4-163-712-0[]
AEP and UK models
PAL
2
4-195-529-0[]
Saudi Arabia model
PAL
3
4-163-714-0[]
E (PAL) model
NTSC
4
4-163-715-0[]
E (NTSC) model
PAL
5
4-163-713-0[]
Russian model
MODEL IDENTIFICATION
Part No.
Region Code
Part No.
Region Code
– Bottom View –
(US and Canadian models)
(US and Canadian models)
– Bottom View –
(AEP, Russian, UK, E and Saudi Arabia models )
(AEP, Russian, UK, E and Saudi Arabia models )
Ver. 1.1
Click on the first or last page to see other XAV-70BT / XAV-E70BT service manuals if exist.