Read Sony WX-7700MDX Service Manual online
9
WX-7700MDX
L
R
L
R
REAR
AUX IN
FRONT
BUS AUDIO
AUDIO OUT
IN
3
1
4
5
6
Blue
Red
Yellow
4
Black
Max. supply current 0.1 A
Fuse (10 A)
BUS AUDIO IN
AMP REM
ANT REM
BUS CONTROL IN
Light blue
Max. supply current 0.3 A
White
Grey
Green
Purple
White/black striped
Grey/black striped
Green/black striped
Purple/black striped
Source selector
XA-C30
Left
Right
Left
Right
3
Blue/white striped
2
ATT
Supplied with the CD/MD changer
Supplied with XA-C30
SUBWOOFER OUT
(MONO)
RCA pin cord
*
1
Orange/white striped
7
ILLUMINATION
*
1
not supplied
*
2
Connect the Bus cable to its
terminal with the unit’s
V
mark and
the Bus cable’s
v
mark aligned.
*
3
supplied with the auxiliary
equipment
*
4
Auxiliary optional equipment such
as portable DVD player (not
supplied)
supplied)
*
2
from car aerial
AUX IN
AUDIO OUT
(REAR)
AUDIO OUT
(FRONT)
RCA pin cord
*
1
*
3
*
4
Notes
• Use the screws
1
or
2
depending on the make of
car. When this unit is attached to a MITSUBISHI car,
use the supplied screws
use the supplied screws
2
.
• T o prevent malfunction, be sure to install using
brackets and the supplied screws
1
or
2
.
• Do not apply excessive force to the buttons of the
unit.
• Do not push on the display window.
• Before mounting, make sure there is nothing on
• Before mounting, make sure there is nothing on
the top of the unit.
Warning when installing in a car
without ACC (accessory)
position on the ignition key
switch
without ACC (accessory)
position on the ignition key
switch
Be sure to press
(OFF)
on the unit for two
seconds to turn off the clock display after
turning off the engine.
turning off the engine.
When you press (OFF) only momentarily, the
clock display does not turn off and this causes
battery wear.
clock display does not turn off and this causes
battery wear.
Reset button
When the installation and connections are
completed, be sure to press the reset button with
a ballpoint pen, etc.
completed, be sure to press the reset button with
a ballpoint pen, etc.
Note
When you connect the power supply cord to the
unit or reset the unit, wait for about 10 seconds
before you insert a disc. If you insert a disc within
these 10 seconds, the unit will not be reset, and you
will have to press the reset button again.
unit or reset the unit, wait for about 10 seconds
before you insert a disc. If you insert a disc within
these 10 seconds, the unit will not be reset, and you
will have to press the reset button again.
Precautions
• Choose the installation location carefully so
that the unit will not interfere with normal
driving operations.
driving operations.
• Avoid installing the unit in areas subject to
dust, dirt, excessive vibration, or high
temperatures, such as in direct sunlight or near
heater ducts.
temperatures, such as in direct sunlight or near
heater ducts.
• Use only the supplied mounting hardware for
a safe and secure installation.
To open/close the front panel smoothly, to insert/
eject a disc easily, and especially to drive safely, a
certain distance between the front panel and the
shift lever is necessary. The necessary distance
differs, depending on the shift lever position of
your car. Before installing the unit, choose the
installation location carefully so that you can
drive safely.
To open/close the front panel smoothly, to insert/
eject a disc easily, and especially to drive safely, a
certain distance between the front panel and the
shift lever is necessary. The necessary distance
differs, depending on the shift lever position of
your car. Before installing the unit, choose the
installation location carefully so that you can
drive safely.
Mounting angle adjustment
Adjust the mounting angle to less than 30
°
.
Frequency select switch
The AM (FM) tuning interval is factory-set to the
9 k (50 k) position. If the frequency allocation
system of your country is based on 10 kHz (200
kHz) interval, set the switch
9 k (50 k) position. If the frequency allocation
system of your country is based on 10 kHz (200
kHz) interval, set the switch
on the bottom of
the unit
to the 10 k (200 k) position before
making connections.
After the frequency select switch is set, you must
press the reset button to reset the unit.
After the frequency select switch is set, you must
press the reset button to reset the unit.
Mounting the unit in a Japanese
car (
car (
4
)
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.
makes of Japanese cars. In such a case, consult
your Sony dealer.
When mounting this unit to the preinstalled
brackets of your car, use the supplied screws 1
or 2 in the appropriate screw holes, according
to your vehicle: T for TOYOTA, M for
MITSUBISHI, and N for NISSAN.
brackets of your car, use the supplied screws 1
or 2 in the appropriate screw holes, according
to your vehicle: T for TOYOTA, M for
MITSUBISHI, and N for NISSAN.
4
A
TOYOTA/MITSUBISHI
to dashboard/centre console
Bracket
Bracket
1
or
2
max. size 5
×
8 mm
Existing parts supplied with your car
1
or
2
max. size 5
×
8 mm
VOL
ANGLE
MODE
SOURCE
DISC
AMS
ATT
OPEN/
CLOSE
OFF
Reset button
T
N
T
M
N
M
T
N
M
N
N
T
T
This illustration is for TOYOTA cars.
B
NISSAN
1
or
2
max. size 5
×
8 mm
Bracket
Existing parts supplied with your car
1
or
2
max. size 5
×
8 mm
to dashboard/centre console
3
WX-7700MDX
WX-7700MDX
Shift lever
88 mm
Bracket
Click on the first or last page to see other WX-7700MDX service manuals if exist.