Read Sony MEX-V50DT Service Manual online
MEX-V50DT
4
Precautions
Choose the installation location carefully so that the
unit will not interfere with normal driving operations.
Avoid installing the unit in areas subject to dust, dirt,
excessive vibration, or high temperature, such as in
direct sunlight or near heater ducts.
Use only the supplied mounting hardware for a safe and
secure installation.
unit will not interfere with normal driving operations.
Avoid installing the unit in areas subject to dust, dirt,
excessive vibration, or high temperature, such as in
direct sunlight or near heater ducts.
Use only the supplied mounting hardware for a safe and
secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 30°.
Connecting the parking brake
lead
lead
Be sure to connect the parking brake lead (light green) of
the power supply connection cable
the power supply connection cable
to the parking
brake switch cord. The mounting position of the parking
brake switch cord depends on your car. Consult your car
dealer or your nearest Sony dealer for further details.
brake switch cord depends on your car. Consult your car
dealer or your nearest Sony dealer for further details.
Installing the One-Seg TV
antenna (aerial)
antenna (aerial)
To enjoy One-Seg TV, you need to install the One-Seg TV
antenna (aerial). Choose the installation location for best
reception.
antenna (aerial). Choose the installation location for best
reception.
1
Screw the One-Seg antenna (aerial) elements
b
to the antenna (aerial) base
a
.
2
Remove the adhesive seal of the antenna (aerial)
base
base
a
, and attach it to the upper part of the
front glass with the cable upwards (as
illustrated).
illustrated).
3
Install a clip (not supplied) and adjust the length
and position of the cord so that is does not
obstruct your driving.
and position of the cord so that is does not
obstruct your driving.
Removing the protection
collar and the bracket
collar and the bracket
Before installing the unit, remove the protection
collar
collar
and the bracket
from the unit.
1
Remove the pre-installed screws.
2
Remove the protection collar
.
Pinch both edges of the protection collar
and
push outwards, then pull out.
3
Remove the bracket
.
Insert both release keys
together between
the unit and the bracket
until they click.
Pull down the bracket
, then pull up the unit
to separate.
Mounting example
Installation in the dashboard
Notes
Bend these claws outward for a tight fit, if necessary
( -2).
Make sure that the 2 catches on the protection collar
are properly
engaged in the slots of the unit
( -3).
How to detach and attach the
front panel
front panel
Before installing the unit, detach the front panel.
-A To detach
Before detaching the front panel, be sure to press
.
Press
, then slide the front panel to the right side,
and pull out the left side.
-B To attach
Engage part
of the front panel with part
of the unit,
as illustrated, and push the left side into position until it
clicks.
clicks.
Warning if your car’s ignition
has no ACC position
has no ACC position
Unnecessary battery drainage will occur if the unit is
wired directly to a car ignition system that does not have
an ACC position. To avoid battery drainage, install a
suitable switch on the ACC line.
wired directly to a car ignition system that does not have
an ACC position. To avoid battery drainage, install a
suitable switch on the ACC line.
Reset button
When the installation and connections are completed, be
sure to press the reset button with a ballpoint pen, etc.
sure to press the reset button with a ballpoint pen, etc.
Foot brake type
Parking brake switch cord
Hand brake type
Parking brake switch cord
1
3
Dashboard
Fire wall
Claws
2
A
B
Red
Red
Yellow
Yellow
Red
Red
Yellow
Yellow
Power connection diagram
The auxiliary power connector may vary depending on
your car. Check your car’s auxiliary power connector
diagram to make sure the connections match correctly.
There are two basic types (illustrated below). You may
need to switch the positions of the red and yellow leads of
the unit’s power supply connection cable
your car. Check your car’s auxiliary power connector
diagram to make sure the connections match correctly.
There are two basic types (illustrated below). You may
need to switch the positions of the red and yellow leads of
the unit’s power supply connection cable
.
After matching the connections and switched power
supply leads correctly, connect the unit to the car’s power
supply. If you have any questions and problems
connecting your unit that are not covered in these
instructions, please consult your car dealer.
supply leads correctly, connect the unit to the car’s power
supply. If you have any questions and problems
connecting your unit that are not covered in these
instructions, please consult your car dealer.
Auxiliary power connector
4
Yellow
Continuous power supply
7
Red
Switched power supply
4
Yellow
Switched power supply
7
Red
Continuous power supply
Face the hook inwards.
1
2
2
3
1
a
b
Clips (not supplied)
a
b
Click on the first or last page to see other MEX-V50DT service manuals if exist.