Read Sony MEX-N5100BE / MEX-N5100BT / MEX-N5150BT Service Manual online
MEX-N5100BE/N5100BT/N5150BT
4
REPLACING THE LITHIUM BATTERY OF THE REMOTE
COMMANDER (Except AEP, UK and Australian models only)
COMMANDER (Except AEP, UK and Australian models only)
Under normal conditions, the battery will last
approximately 1 year. (The service life may be
shorter, depending on the conditions of use.)
When the battery becomes weak, the range of the
remote commander becomes shorter.
approximately 1 year. (The service life may be
shorter, depending on the conditions of use.)
When the battery becomes weak, the range of the
remote commander becomes shorter.
CAUTION
Danger of explosion if battery is incorrectly
replaced. Replaced only with the same or
equivalent type.
replaced. Replaced only with the same or
equivalent type.
+ side up
Notes on the lithium battery
ˎ Keep the lithium battery out of the reach of children.
Should the battery be swallowed, immediately
consult a doctor.
consult a doctor.
ˎ Wipe the battery with a dry cloth to ensure a good
contact.
ˎ Be sure to observe the correct polarity when installing
the battery.
ˎ Do not hold the battery with metallic tweezers,
otherwise a short-circuit may occur.
DESTINATION ABBREVIATIONS
The following abbreviations for model destinations are used in this
service manual.
The following abbreviations for model destinations are used in this
service manual.
• Abbreviations
AUS :
AUS :
Australian
model
CND : Canadian model
EA
EA
: Saudi Arabia model
IND
: Indian model
MX
: Mexican model
RU
: Russian model
DESTINATION SETTING METHOD
When the complete MAIN board or IC502 on the MAIN board is
replaced, the destination setting is necessary.
When the complete MAIN board or IC502 on the MAIN board is
replaced, the destination setting is necessary.
1. Destination
Setting
Set destination according to the procedure below.
1-1. Setting the Destination Code
1. In the state of source off (the clock is displayed), enter the test
1. In the state of source off (the clock is displayed), enter the test
mode by pressing the buttons in order of the [
4]
t [MIC
5]
t [PAUSE 6] (press only the [PAUSE 6] button for two
seconds).
2. In the state in which the software main version is displayed on
the liquid crystal display (refer to following fi gure), enter the
destination setting mode by pressing the buttons in order of the
[
destination setting mode by pressing the buttons in order of the
[
> M
SEEK+]
t [SEEK–
m
.
]
t [PUSH ENTER/
VOICE].
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
Software main version
3. Input the alphanumeric character of 12 digits of “F XXXXXX”
displayed on the liquid crystal display, and execute the destina-
tion setting.
tion setting.
Note: Refer to following “1-3. Entering the Destination Code” for opera-
tion method.
4. The resetting operation is executed by pressing the [
OFF
SRC] button for 1 second after the setting ends, and the unit
returns to the normal condition.
returns to the normal condition.
1-2. Display in Destination Setting Mode
(Displayed characters/values in the following fi gure are example)
(Displayed characters/values in the following fi gure are example)
12 digits
OP5 OP4 OP3 OP2 OP1 OP0
Destination code
1-3. Entering the Destination Code
•
•
Method of operation by main unit
1. Rotate the control dial, and select the alphanumeric character
of “0 to F”.
2. The digit advances by pressing the [PUSH ENTER/VOICE] or
[
> M
SEEK+] button.
The digit returns by pressing the [
MODE] or [SEEK–
m
.
] button.
3. The setting is completed by pressing the [PUSH ENTER/
VOICE] button, then the display turns off, the initialization
operation is done, and the display returns to the clock display.
operation is done, and the display returns to the clock display.
•
Method of operation by remote commander
(Except AEP, UK and Australian models only)
Note: The model to which the remote commander is not attached can
also be operated by using the remote commander.
1. Press
the
[V] or [v] button, and select the alphanumeric char-
acter of “0 to F”.
2. The digit advances by pressing the [b] or [ENTER] button.
The digit returns by pressing the [B] button.
3. The setting is completed by pressing the [ENTER] button, then
the display turns off, the initialization operation is done, and
the display returns to the clock display.
the display returns to the clock display.
– Continued on next page –
Click on the first or last page to see other MEX-N5100BE / MEX-N5100BT / MEX-N5150BT service manuals if exist.